Electrical Installation - Oase Water Jet Lightning Mode D'emploi Et Consignes De Sécurité

Pos: 32 /Alle Produkte/Überschriften/H1 Elektrische Installation @ 8\mod_1219935543509_121.doc @ 51295 @

Electrical installation

Pos: 33 /Lampen/Wasserspieltechnik/Water Jet Lightning/INS_Water-Jet-Lightning @ 8\mod_1221039895037_121.doc @ 52213 @
Connect the Water Jet Lightning with the 12 V control box and the transformer (H, I)
− Insert the pump plug (23) from the plug and the plugs (24) of the two Water Jet Lightning units into the respective
sockets for the pump (25) and the Water Jet Lightning (26) at the 12 V control box (2).
− Screw-connect the plug (27) of the transformer connection cable on the secondary side to the socket (28) at the rear
of the 12 V control box (2) and screw tighten with the union nut (29).
− Place the protection hood (3) over the 12 V control box (2).
Note: If you only want to operate one of the two Water Jet Lightning systems, plug the jumper plug (49) into the second
free socket (26).
n
Pos: 34 /Lampen/Wasserspieltechnik/Water-Jet Lightning USA/Inbetriebnahme Water Jet Lightning USA @ 10\mod_1235556937962_121.doc @ 60728 @
Start-up
Caution! Do not damage the unit.
Protective measures: Never run the unit without water. Otherwise the pump will be destroyed.
The unit switches on automatically when connected to power. Attention: Note DC +/- polarity.
Switching on the unit (J): Plug the power plug (30) of the transformer into the socket.
− The unit will start with program 1 (see chapter 'Control/Operation').
Switching off the unit (J): Pull the power plug (30) of the transformer.
Pos: 35 /Lampen/Wasserspieltechnik/Water Jet Lightning/Ausrichten Water-Jet-Lightning @ 8\mod_1221040206242_121.doc @ 52317 @
Alignment of the Water Jet Lightning and setting the intensity of the water jet (L, M)
Prior to starting work, disconnect the power plugs of all units in the water (J)!
Adjusting the angle of inclination (L)
The diagram shows the shapes of the water jet at various angles of inclination of the Water Jet Lightning.
− Undo the fastening screw (34) at the unit foot (33).
− Swing the Water Jet Lightning to the desired angle of inclination.
− Tighten the fastening screw (34) at the unit foot (33).
Setting the water jet (M)
For the Water Jet Lightning, the intensity of the water jet can be set at the valves of the Y distributor (9).
− Turn the respective valve clockwise: to reduce the water flow.
− Turn the respective valve counter-clockwise: to increase the water flow.
Pos: 36 /Alle Produkte/Überschriften/H1 Bedienung @ 7\mod_1196625148604_121.doc @ 41443 @
Operation
Pos: 37 /Lampen/Wasserspieltechnik/Water Jet Lightning/BED_Water-Jet-Lightning @ 8\mod_1221040043053_121.doc @ 52265 @
4 pre-programmed water features can be selected with the manual transmitter.
After commissioning and with each new start of the unit, program 1 is automatically selected.
P0
P1
P2
P3
P4
Selecting the next program: Button 1
Selecting the previous program: Button 2
Note:
− From changing light colour, it is possible to set one colour only by pressing the buttons 1 and 2 simultaneously.
− If the Water Jet Lightning is switched by means of a timer, always program 1 is started.
Pos: 38 /Alle Produkte/Dummy_module/===== Seitenwechsel ===== @ 0\mod_1125648978015_0.doc @ 1631 @
Unit off, stand-by mode
Constant water jet
White light activated
Constant water jet
Changing light colours
Pulsating water jet
White light activated
Pulsating water jet
Changing light colours
Changing light colour can be returned to by pressing the buttons 1 and 2 simultaneously again.
- English -
11