Black & Decker BDCHD18 Mode D'emploi page 5

Masquer les pouces Voir aussi pour BDCHD18:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
Labels on tool
Additional safety instructions for batteries and
chargers (Not provided with the tool)
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
The following symbols are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Batteries
Never attempt to open for any reason.
Do not expose the battery to water.
Do not store in locations where the temperature may
exceed 40 °C.
Charge only at ambient temperatures between 10 °C and
40 °C.
Charge only using the charger provided with the tool.
When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
Chargers
Use your BLACK+DECKER charger only to charge the
battery in the tool with which it was supplied. Other batter-
Never attempt to charge non-rechargeable batteries.
Have defective cords replaced immediately.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The charger is intended for indoor use only.
Read the instruction manual before use.
measures required by 2002/44/EC to protect persons regularly
:
u
u
u
u
u
u
p
u
ies could burst, causing personal injury and damage.
u
u
u
u
u
$
+
Features
Assembly
Use
(Original instructions)
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the
charger unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
This tool includes some or all of the following features.
1. Variable speed switch
4. Keyless chuck
5. Dual range gearing
6. LED work light
7. Battery
8. Battery release button
9. Screwdriver bit holder
Warning! Let the tool work at its own pace. Do not overload.
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
Plug the charger into any standard 230 Volts 50 Hz electri-
cal outlet.
ing charged.
The completion of charge is indicated by the green LED
remaining on continuously. The pack is fully charged and
may be used at this time or left on the charger.
Warning! fire Hazard. When disconnecting the charger from
then disconnect the charger cord from the tool.
#
u
2. Forward/reverse slider
3. Torque adjustment collar
Charging the battery (fig. A)
The battery needs to be charged before first use and whenev-
er it fails to produce sufficient power on jobs that were easily
u
Slide the battery pack into the charger as shown in fig. A.
u
The green LED will flash indicating that the battery is be-
u
u
the tool, be sure to unplug the charger from the outlet first,
ENGLISH
5

Publicité

Table des Matières
loading

Table des Matières