Technical Data; Before Starting The Equipment; Assembling The Components - EINHELL GC-PM 51/2 S HW-E Instructions D'origine

For safety reasons, the lawn mower may not be
used as a drive unit for other work tools or toolkits
of any kind.

4. Technical data

Engine type ........One-cylinder four-stroke engine,
.......................................................173 cc/2.7 kW
Working speed n : ...................... 2900 ± 100 min
0
Fuel: ............................................................ Petrol
Tank capacity: .................................. approx. 1.5 l
Engine oil: ........................... approx. 0.6 l / 10W30
Spark plug: ................................................ F7RTC
Cutting height adjustment: ... Central, (30-80 mm)
Cutting width: .......................................... 510 mm
Weight: ......................................................41,5 kg
Battery charger
Mains voltage: ................100-240V AC ~ 50/60Hz
Nominal output voltage: ....................... 14,5 V DC
Nominal output current: ................................ 0.8 A
Battery capacity: .......................................... 7 Ah
Protection class:............................................II /
Battery voltage: ............................................. 12V
Sound and vibration
L sound pressure level ..................... 81.9 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 98 dB(A)
WA
K uncertainty ........................................ 1.96 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Vibration emission value a
K uncertainty = 1.5 m/s
Long work periods should be avoided due to the
development of high noise and vibration levels.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
Anl_GC_PM_51_2_S_HW_E_SPK1.indb 34 Anl_GC_PM_51_2_S_HW_E_SPK1.indb 34
-1
&
= 4.5 m/s
2
h
2
- 34 -
GB
•
Switch the appliance off when it is not in use.

5. Before starting the equipment

5.1 Assembling the components

Some parts of the mower come disassembled.
For quick and easy assembly, read and follow the
instructions below.
Important. You will need the following additional
tools (not supplied) for assembly, and also for
maintenance work:
•
A flat oil drip tray (for changing the oil)
•
A 1 liter measuring jug (oil/petrol resistant)
•
A petrol can
•
A funnel (suitable for the tank's petrol filler
neck)
•
Household wipes (to wipe up oil/petrol resi-
due; dispose of these at a filling station)
•
A petrol suction pump (plastic, available from
DIY stores)
•
An oil can with hand pump (available from
DIY stores)
•
Engine oil
Assembly
1. Fit the lower and upper push bar (Item. 3) as
shown in Fig. 3a-3b. For fastening choose
one of the holes to suit the required height of
the push bar. Important! The identical height
must be set on both sides.
2. Insert the grip of the starter cord (Item 9a) into
the hook provided for that purpose as shown
in Figure 3c.
3. Fasten the cords to the push bar with the sup-
plied cable clips (Item 10).
4. Lift the ejector fl ap (Item 5a) with one hand
and hook in the grass bag (Item 4a) as shown
in Figure 4a..
Important. Whenever you do any work on the
battery and when you dispose of the battery, you
must observe the safety regulations of the manu-
facturer.
Warning! The person entrusted with inserting the
battery should remove all metal armbands, wrist-
watches, rings and similar before starting to insert
the battery. There is a risk of burns if any of these
objects should come into contact with the battery
poles or current-conducting cables.
Warning! Check the insulation on the cables
and plugs each time before use. If there are any
defects in the insulation, the equipment must not
19.10.2015 12:52:57 19.10.2015 12:52:57