EdilKamin KIKKA PLUS Installation, Usage Et Maintenance page 43

LOADING THE SCREW FEEDER
(with the stove oFF - Function not active with
timer ON)
Loading the pellet screw feeder (coclea) is only necessary if the
stove is new (and being switched on for the fi rst time) or if the
stove had completely run out of pellets.
To activate this refi ll operation press the
seconds and scroll down the parameters on the display using
the same button until it displays the word "Menu".
Confi rm with the button and scroll down through the
Menu, using the button until it displays the message
"Load" and confi rm with the
By confi rming the "Load" option you automatically return to
the main screen and the stove is forced to the specifi c "Load"
phase lasting 240 seconds.
To stop prematurely, press the
for a few seconds. The stove will return to "oFF". The "Load"
sub-menu is available to users only if the stove is OFF.
IGNITION
By pressing the button, the message "Load" appears on
the display (this is the pre-load phase prior to ignition).
The display will then automatically show the message "Strt"
and when the pellets have been ignited the word "FirE" appe-
ars.
At this point, the stove ignition is completed and it can operate
in manual mode or automatic mode.
SWITCHING OFF
If you press the button for a few seconds, the switch-off
phase will start.
During the switch-off phase the words "doWn" and "cooL"
appear on the display.
You will not be able to switch the stove back on again; once the
switch-off phase is completed, the system will automatically go
back to stand-by mode (the word OFF appears on the display).
MANUAL/AUTOMATIC SETTING
Press the button for a few seconds and scroll down
the parameters on the display using the same button until it
displays the word "Menu".
Confi rm with the button and scroll down through the
Menu, using the button until it displays the message
"Auto" and confi rm with the
To set the AUTOMATIC mode, press the
message "A on" is displayed. Confi rm with the
To set the MANUAL mode, press the
message "A off" is displayed. Confi rm with the
INSTRUCTIONS FOR USE
button for a few
button.
tbutton holding it down
button.
button and the
button.
button and the
button.
- 43
At this point, the word "Auto" appears on the display. Scroll
down through the Menu by pressing the
when the word "quit" is displayed confi rm with
button, scroll down by pressing the
word "quit" is displayed and press the
AUTOMATIC REGULATION
By briefl y pressing the
appears on the display, and it sets the value at which you want
the stove to work.
To activate the automatic mode, set to "A on" as described in
the previous paragraph.
MANUAL REGULATION
By briefl y pressing the
appears on the display, by briefl y pressing the
message SET POWER is displayed.
You can increase the desired power (from P1 to P5) by pressing
the button or decrease it by pressing the
To activate the manual mode, set to "A off" as described in the
previous paragraph.
In both regulation modes, by briefl y pressing the
the main screen is displayed.
If no button is pressed within a certain time, the display will
show the main screen automatically.
ECO STOP FUNCTION
By briefl y pressing the
sage "E on" is displayed (function ON) or "E off" (function
OFF).
To activate the ECO STOP function, press the
the message "E on" is displayed and confi rm with the
To deactivate the ECO STOP function, press the
and the message "E off" is displayed and confi rm with the
.
It can only be activated in automatic mode ("A on").
It is a function that is suitable when the stove is installed in
small rooms or, during mid-seasons, when even a minimum
power setting still tends to overheat the room.
This function is managed automatically, and allows you to
switch off the stove when the desired room temperature is
exceeded.
When the room temperature falls below the set value, the stove
automatically switches back on.
-
, button and
button until the
button
sbutton, the message SET ROOM
button, the message SET ROOM
button, the
button.
button,
buttons, the mes-
button and
button
.