Maintenance And Service; Maintenance And Cleaning; Maintenance Schedule - Bosch GCN 45-15 Professional Notice Originale

OBJ_BUCH-1303-001.book Page 19 Friday, March 25, 2011 11:07 AM
Transport and Storage
For transport, disconnect the pneumatic tool from the air supply; espe-
cially when using ladders or moving in an unusual stance or posture.
At the workplace, carry the pneumatic tool only by the handle 2 and with
the trigger released.

Maintenance and Service

Maintenance and Cleaning

Disconnect the air supply before making any adjust-
ments, changing accessories, or placing the pneumatic
tool aside. This safety measure prevents accidental start-
ing of the pneumatic tool.
If the pneumatic tool should fail despite the care taken in manufacture and
testing, repair should be carried out by an authorised customer services
agent for Bosch power tools.
In all correspondence and spare parts orders, please always include the
10-digit article number given on the type plate of the pneumatic tool.
Have maintenance and repair work carried out only through quali-
fied persons. This will ensure that the safety of the pneumatic tool is
maintained.
An authorized Bosch after-sales service agent will carry out this work
quickly and reliably.

Maintenance Schedule

Always keep air outlet 1, discharge lock-off 10 and trigger clean and free
of foreign material (dust, chips, sand, etc).
Measure
Draining the exhaust filter daily.
Keeping the lubricator filled at all times.
Cleaning the magazine 6 and the feeder
hook 22.
Ensuring that the discharge lock-off 10
functions properly.
Lubricating the pneumatic tool.
Draining the compressor.
Bosch Power Tools
Always store the pneumatic tool disconnected from the air supply and at
a clean and dry location.
When not using the pneumatic tool for a longer period of time, cover steel
parts with a fine oil coating. This prevents the formation of rust.
Lubricating the Pneumatic Tool (see figure I)
When the pneumatic tool is not connected to a maintenance unit, it must
be lubricated at regular intervals:
– For light-duty use 1x per day.
– For heavy-duty use 2x per day.
Apply 2
–
lubricant, which could then accumulate in the pneumatic tool and be emit-
ted via air outlet 1.
Use only the lubricants recommended by Bosch.
– SAE 10 mineral engine oil (for use at very cold ambient conditions)
– SAE 20 mineral engine oil
Observe all applicable environmental regulations when disposing of
old grease and solvents.
Removing Debris/Contamination from Tar (see figure J)
When fastening roofing felt, the pneumatic tool can become contaminat-
ed from tar.
For cleaning, use only flame-retardant solvents and clean the dis-
charge lock-off and the outlet with a clean cloth.
Wear protective gloves.
Clean the magazine 6. Remove any plastic or wood chips that may accu-
mulate in the magazine during operation.
Clean the pneumatic tool in regular intervals using compressed air.
Explanation
Prevents the accumulation of dirt/ debris and
moisture in the pneumatic tool.
Ensures the lubrication of the pneumatic tool.
Prevents the jamming of nails.
Promotes your work safety and efficient usage of
the pneumatic tool.
Reduces the wear of the pneumatic tool.
Prevents the accumulation of dirt/ debris and
moisture in the pneumatic tool.
3 drops of lubricant into air connector 3. Do not apply too much
Action
– Open the drain valve.
– Fill lubricator with the recommended lubricants.
(See "Lubricating the Pneumatic Tool", page 19)
– Blow out the mechanism of the magazine/feeder
hook daily with compressed air.
– Blow out the mechanism of the discharge lock-off
daily with compressed air.
– Apply 2 3 drops of lubricant into air connector 3.
–
(See "Lubricating the Pneumatic Tool", page 19)
– Open the drain valve of the compressor tank.
English | 19
1 609 929 X29 | (25.3.11)