Installation Warnings - Nice SWN 70-24 Manuel D'installation Et D'utilisation

GENERAL WARNINGS: SAFETY - INSTALLATION - USE (original instructions in Italian)
ATTENTION Important safety instructions. Follow all instructions as improper installation may cause serious damage
ATTENTION Important safety instructions. It is important for you to comply with these instructions for your own and other
people's safety. Keep these instructions.
• Before commencing the installation, check the "Technical characteristics" (in this manual), in particular whether this product is suitable for
automating your guided part. If it is not suitable, DO NOT continue with the installation
•
ATTENTION According to the most recent European legislation, the implementation of an automation system must comply
with the harmonised standards provided by the Machinery Directive in force, which enables declaration of the
presumed conformity of the automation. Taking this into account, all operations regarding connection to the
electricity grid, as well as product testing, commissioning and maintenance, must be performed exclusively by
• Before proceeding with the installation of the product, check that all the materials are in good working order and suited to the intended
applications
• This product is not intended to be used by persons (including children) whose physical, sensory or mental capacities are reduced, or who
lack the necessary experience or skill
• Children must not play with the appliance
•
ATTENTION In order to avoid any danger from inadvertent resetting of the thermal cut-off device, this appliance must not be powered
through an external switching device, such as a timer, or connected to a supply that is regularly powered or switched off by
the circuit
• Provide a disconnection device (not supplied) in the plant's power supply grid, with a contact opening distance permitting complete
disconnection under the conditions dictated by overvoltage category III
• Handle the product with care during installation, taking care to avoid crushing, denting or dropping it, or allowing contact with liquids of any
the risk of danger or malfunction. Should this happen, stop installation immediately and contact Customer Service
• The manufacturer assumes no liability for damage to property, items or persons resulting from non-compliance with the assembly instructions.
In such cases the warranty for material defects is excluded
• The weighted sound pressure level of the emission A is lower than 70 dB(A)
• Cleaning and maintenance to be carried out by the user must not be carried out by unsupervised children
• Before working on the system (maintenance, cleaning), always disconnect the product from the mains power supply
• Check the system periodically, in particular all cables, springs and supports to detect possible imbalances, signs of wear or damage. Do not
use, if repairs or adjustments are necessary, since installation failure or an incorrectly balanced automation may cause injury
• The packing materials of the product must be disposed of in compliance with local regulations
• The product must not be installed outdoors
•
• • Be careful when activating the manual release device, as an open door may fall suddenly due to weak or broken springs, or if it is
unbalanced
• Every month, check that the drive motor reverses when the door encounters a 50 mm-high object placed on the ground. If necessary,
readjust the door and check it again, as incorrect adjustment is potentially dangerous (for drive motors incorporating a trapping safety
system that intervenes when the door's lower edge encounters an obstacle)
•
person, in order to prevent any type of risk
• Prior to installing the drive motor, check that the door is in good working order, correctly balanced and that it opens and closes properly
• Prior to installing the motor, remove all unnecessary cables or chains and deactivate any equipment – such as locking devices – not required
for motorised operation
•
closed position; adequately protect any such parts
• Install the manoeuvring assembly for manual release at a height below 1.8 m
NOTE: if removable, the manoeuvring assembly must be kept close to the door
• Make sure that the control devices are kept far from moving parts but nonetheless in a visible position.
Unless a selector is used, the control devices must be installed at a height of at least 1.5 m and must not be accessible
•
• Permanently attach the manual release label close to the manoeuvring assembly
• After installation, make sure that the motor prevents or stops door opening when the latter is loaded with a 20 kg weight secured to the
centre of its bottom edge (for drive motors that can be used with doors having opening widths exceeding 50 mm)
• After installation, make sure that the mechanism is properly adjusted and that the motor reverses when the door collides with a 50 mm-tall
object placed on the ground (for drive motors incorporating a trapping safety system that intervenes when the bottom edge of the door
encounters an obstacle).

INSTALLATION WARNINGS

English – 1