Declaration Of Conformity; Personal Safety - Hilti DSH 600 Mode D'emploi

▶ Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to enquire about the product.
Product information
Cut-off saw
Generation
Serial no.

1.6 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives
and standards. A copy of the declaration issued by the certification department can be found at the end of
this documentation.
The technical documentation is filed and stored here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany
2 Safety

2.1 Personal safety

▶ Use the right tool for the job. Do not use the tool for purposes for which it was not intended. Use it only
as directed and when in technically faultless condition.
▶ Never tamper with or modify the tool in any way.
▶ Only persons who are familiar with it, who have been trained on how to use it safely and who understand
the resulting hazards are permitted to use the tool. The tool is not intended for use by children.
▶ Stay alert, watch what you are doing and use common sense when operating the tool. Do not use the
tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention
while operating the tool can result in serious personal injury.
▶ The user and persons in the vicinity must wear ANSI Z87.1-approved protective goggles, a hard hat, ear
protectors, protective gloves, protective footwear and light respiratory protection while the tool is in use.
▶ Always hold the tool firmly with both hands on the grips provided. Keep the grips dry, clean and free
from oil and grease.
▶ Never use the tool without the guard (hood). Adjust the guard to the correct position. The guard must be
securely attached and positioned for maximum safety, so that the smallest possible part of the cutting
disc is exposed to the operator. Make sure that sparks created during use do not present a hazard. The
guard helps to protect the operator from broken disc fragments, inadvertent contact with the cutting disc
and uncontrolled flying sparks.
▶ Before using the tool, or if an obstacle is contacted while the tool is in use, check the guard immediately
for possible damage. Replace the guard immediately if it is damaged or broken.
▶ Do not touch rotating parts – risk of injury!
▶ Maintain a firm footing and balance at all times. This will allow you to control the tool better, even in
unexpected situations, for example, in the event of experiencing kickback or rotational forces. Avoid
unusual postures.
▶ Wear suitable work clothes. Do not wear jewelry or loose clothing. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry or long hair can be snagged by moving parts.
▶ Releasing the throttle safety grip when the tool is running at full speed causes the tool to flick forward
slightly because of the braking torque. Be prepared for this and keep a firm grip on the tool with both
hands on the grips provided.
▶ If the tool or the cutting disc has been dropped or has fallen, check the tool and the cutting disc for
damage. Change the cutting disc if necessary.
▶ Switch the tool off before adjusting the guard or changing the cutting disc.
▶ Wear protective gloves when changing the cutting disc. Touching the cutting disc presents a risk of
injury (cuts or burns).
▶ Make sure fire extinguishers are available for use as there is a risk of fire due to flying sparks and the use
of flammable fuel.
▶ Do not use reducing sleeves.
▶ Use of the wet cutting method is preferable in order to reduce the amount of dust produced when cutting
mineral materials and asphalt.
▶ Avoid skin contact with the slurry created when using the wet cutting method.
▶ Dust from materials such as paint containing lead, some types of wood, minerals and metal can be
harmful to health. Contact with or inhalation of the dust can cause allergic reactions and/or respiratory or
Printed: 30.03.2017 | Doc-Nr: PUB / 5341985 / 000 / 00
DSH 600 | DSH 600-X
01
English 3