Dremel 4300 Consignes De Fonctionnement/Sécurité page 5

1600A00N3H.qxp_4300 7/8/16 10:33 AM Page 5
and/or incorrect operating procedures or
conditions and can be avoided by taking proper
precautions as given below.
Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. The operator can
control torque reactions or kickback forces, if
proper precautions are taken.
Use special care when working corners,
sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or
kickback.
Do not attach a toothed saw blade. Such
blades create frequent kickback and loss of
control.
Always feed the bit into the material in the
same direction as the cutting edge is exiting
from the material (which is the same
direction as the chips are thrown). Feeding
the tool in the wrong direction causes the
cutting edge of the bit to climb out of the work
and pull the tool in the direction of this feed.
When using rotary files, cut-off wheels,
high-speed cutters or tungsten carbide
cutters, always have the work securely
clamped. These wheels will grab if they
become slightly canted in the groove, and can
kickback. When a cut-off wheel grabs, the
wheel itself usually breaks. When a rotary file,
high-speed cutter or tungsten carbide cutter
grabs, it may jump from the groove and you
could lose control of the tool.
Safety warnings specific
for grinding and abrasive
cutting-off operations:
Use only wheel
recommended for your power tool and only
for recommended applications. For
example: do not grind with the side of a cut-
off wheel. Abrasive cut-off wheels are intended
for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
For threaded abrasive cones and plugs use
only undamaged wheel mandrels with an
unrelieved shoulder flange that are of
correct size and length. Proper mandrels will
reduce the possibility of breakage.
Do not ''jam'' a cut-off wheel or apply
excessive pressure. Do not attempt to make
an excessive depth of cut. Overstressing the
wheel increases the loading and susceptibility
Safety Rules for Rotary Tools - (cont.)
types that
to twisting or snagging of the wheel in the cut
and the possibility of kickback or wheel
breakage.
Do not position your hand in line with and
behind the rotating wheel. When the wheel,
at the point of operation, is moving away from
your hand, the possible kickback may propel
the spinning wheel and the power tool directly
at you.
When wheel is pinched, snagged or when
interrupting a cut for any reason, switch off
the power tool and hold the power tool
motionless until the wheel comes to a
complete stop. Never attempt to remove the
cut-off wheel from the cut while the wheel is
in motion otherwise kickback may occur.
Investigate and take corrective action to
eliminate the cause of wheel pinching or
snagging.
Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully re-enter the cut. The wheel may
bind, walk up or kickback if the power tool is
restarted in the workpiece.
Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under
their own weight. Supports must be placed
under the workpiece near the line of cut and
near the edge of the workpiece on both sides of
the wheel.
Use extra caution when making a ''pocket
cut'' into existing walls or other blind areas.
The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can cause
kickback.
Safety warnings specific for wire
brushing operations:
are
Be aware that wire bristles are thrown by
the brush even during ordinary operation.
Do not overstress the wires by applying
excessive load to the brush. The wire bristles
can easily penetrate light clothing and/or skin.
Allow brushes to run at operating speed for
at least one minute before using them.
During this time no one is to stand in front
or in line with the brush. Loose bristles or
wires will be discharged during the run-in time.
Direct the discharge of the spinning wire
brush away from you. Small particles and tiny
wire fragments may be discharged at high
velocity during the use of these brushes and
may become imbedded in your skin.
5