Before Operation; Working With Your Machine - Viking LE 540 Manuel D'utilisation

Masquer les pouces Voir aussi pour LE 540:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 43
accessory) on the load floor using
adequately dimensioned fastening
material (belts, ropes, etc.).
Avoid contact with the blades when lifting
and carrying the machine.
Observe the information in the section
"Transport". It describes how to lift and
lash the machine. (
12.1)
When transporting the machine, always
observe regional legislation, especially
regarding load security and the transport
of objects on load floors.

4.5 Before operation

Make sure that only persons who are
familiar with the instruction manual are
permitted to use the machine.
Observe the instructions in section
"Dangers caused by electrical current"
(
4.2).
Observe the local regulations regarding
permitted operating times for gardening
power tools with electric motors.
The machine must not be used on paved
or gravelled surfaces where ejected
material can cause injuries.
Carefully inspect the complete area on
which the machine is to be used and
remove any stones, sticks, wires, bones
and other foreign objects which could be
thrown up by the machine. Obstacles (e.g.
tree stumps, roots) can be easily
overlooked in long grass.
For this reason, mark all foreign objects
(obstacles) which are hidden in the lawn
and cannot be removed before
commencing work with the machine.
0478 670 9902 H - EN
All faulty, worn or damaged parts must be
replaced before using the machine.
Replace any illegible or damaged danger
signs and warnings on the machine. Your
VIKING specialist has a supply of
replacement stickers and all the other
spare parts.
The machine must only be used in good
operating condition. Before each use,
check whether:
– The machine is properly assembled.
– The scarifying unit (blade shaft, blades,
spacer bushings and fastening) are in
perfect condition – in particular check
for secure fastening, damage (notches
or cracks) and wear.
– The safety devices (e.g. discharge flap
with rubber sheet, housing, handlebar,
motorstop lever) are in perfect condition
and working properly.
– The grass catcher box (accessory – not
included in standard equipment) is
undamaged and correctly installed – a
damaged grass catcher box must not
be used.
Carry out any necessary work or consult a
specialist dealer. VIKING recommends
VIKING specialist dealers.

4.6 Working with your machine

Never work when animals or
persons, particularly children,
are in the danger area.
The switch and safety devices installed in
the machine must not be removed or
bypassed. In particular, never secure the
motorstop lever to the handlebar (e.g. by
tying it).
The handlebar must always be installed
correctly and must not be modified. Never
operate the machine with the handlebar
folded down.
Never attach any objects to the handlebar
(e.g. work clothing). Extension cables
must never be wrapped around the
handlebar.
Only work during the day or with good
artificial light.
Do not operate the machine in the rain or
during thunder storms, particularly when
there is a risk of lightning strike.
The risk of accidents is higher if the ground
is damp due to increased danger of
slipping.
Particular caution should be exercised
during working in order to prevent slipping.
If possible, avoid using the machine when
the ground is damp.
Do not leave the machine in the rain.
Switching on the machine:
Exercise care when switching on the
machine and observe the instructions in
the section "Operating the machine".
(
10.)
Ensure that you keep your feet far enough
away from the blades.
Always place the scarifying unit in the
transport position before starting it.
Place the machine on an even surface
before switching it on.
The machine must not be tilted before it is
switched on or during switching-on.
Do not switch on the motor if the discharge
chute is not covered by the discharge flap
or the grass catcher box (accessory – not
included in standard equipment).
29

Publicité

Table des Matières
loading

Table des Matières