Symbols; Selection Charts - 3M Graco 50261 Manuel D'instructions

Warning Symbol
WARNING
This symbol alerts you to the possibility of serious injury or
death if you do not follow the instructions.
EQUIPMENT
Misuse can cause death or serious
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical
Data in all equipment manuals. • Use fluids and solvents that
INSTRUCTIONS
in all equipment manuals. Read fluid and solvent
damaged parts immediately. • Do not alter or modify equipment. • Route hoses and cables away from traffic areas, sharp edges,
moving parts, and hot surfaces. • Do not use hoses to pull equipment. • Comply with all applicable safety regulations.
• This equipment is to be used only by professional tradesmen who are familiar with its possible hazards. • Read all instruction
manuals, tags, and labels before operating the equipment. • Use the equipment only for its intended purpose. See intended use
statement on front cover.
PRESSURIZED EQUIPMENT
To reduce the risk of a serious injury, follow the Pressure Relief Procedure
relieve pressure.
• Do not stop or deflect fluid leaks with your hand, body, glove or rag.
• Do not point the spray gun at anyone or at any part of the body.
FIRE AND EXPLOSION
Flammable fumes, such as solvent and paint fumes, in work
To help prevent fire and explosion:
• Use equipment only in well ventilated area. • Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric
lamps, and plastic drop cloths (potential static arc). • Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present. • Ground equipment and
conductive objects in work area. See Grounding instructions on page 6. • If there is static sparking or you feel a shock,
stop operation immediately. Do not use equipment until you identify and
TOXIC FLUID OR FUMES
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed.
• Read MSDS's to know the specific hazards of the fluids you are using. • Store hazardous fluid in approved containers,
and dispose of it according to applicable guidelines. • Gloves must be worn for spraying or cleaning the equipment.
Spray Gun Assemblies
HVLP Guns -
for high efficiency
with low pressure
Air Spray Guns
Compliant Guns
† Measured with gun nozzle 203mm (8in.)
from target surface
Selecting the Proper Nozzle Size
Follow your material suppliers
light viscosity materials and larger nozzle sizes for higher flows and higher viscosity materials.

Symbols

MISUSE HAZARD
injury.
HAZARD
HAZARD
HAZARD

Selection Charts

Gun and PPS Cup
Assembly. Part No.
50261
50262
50263
50255
50256
50257
50258
50259
recommendations for proper nozzle size. In general, use the smaller nozzle sizes for low flow rates or
Caution Symbol
This symbol alerts you to the possibility of damage to or
destruction of equipment if you do not follow the instructions.
WARNING
are compatible with equipment wetted parts. See Technical Data
manufacturers' warnings. • Check equipment daily. Repair or replace worn or
areas can ignite or explode.
correct the problem.
Orifice Size Pattern Length
mm (in.) mm (in.)
1.3 (.051) 330 (13)
1.4 (.055) 330 (13)
1.5 (.059) 330 (13)
1.5 (.059) 228 (9)
1.8 (.070) 228 (9)
1.3 (.051) 279 (11)
1.4 (.055) 279 (11)
1.5 (.059) 279 (11)
2
CAUTION
on page 6 whenever you are instructed to
† Air Cap
Marking
H
H
H
A
A
C
C
C
Housing
Colour
Purple
Purple
Purple
Black
Black
Gold
Gold
Gold