Intended Use; Technical Data - EINHELL TC-WW 1000/1 Instructions D'origine

•
Locking grip
•
Wrench for pinion shaft
•
Face plate
•
Crank handle
•
Hexagon key
•
Wrench for front end driver ring
•
Screw, small (3x)
•
Washer, small (6x)
•
Spring washer (3x)
•
Nut, small (3x)
•
Screw, large (2x)
•
Washer, large (2x)
•
Wing nut (2x)
•
Washer for crank handle
•
Original operating instructions
•
Safety information

3. Intended use

The wood lathe is only designed for working on
wood using a suitable turning tool..
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Mains voltage: .............................. 230 V ~ 50 Hz
Power: ...................................400 Watt S2 30 min
Idle engine speed ...............................1,400 min
Spindle speed ............890/1260/1760/2600 min
Tip width ................................. approx. 1,000 mm
Max. lathe diameter ................................ 280 mm
Protection type: .......................................... IP 20
Weight: ........................................................23 kg
Load factor:
A load factor of S2 30 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (400
W) for no longer than the time stipulated on the
specifi cations label (30 min). If you fail to observe
Anl_TC_WW_1000_1_SPK9.indb 18 Anl_TC_WW_1000_1_SPK9.indb 18
GB
this time limit the motor will overheat. During the
OFF period the motor will cool again to its starting
temperature.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
Operation
L sound pressure level ........................ 61 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 74 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although
there is a correlation between emission and im-
mission levels it is impossible to draw any certain
conclusions as to the need for additional precau-
tions. Factors with a potential infl uence on the ac-
tual immission level at the workplace include the
duration of impact, the type of room, and other
sources of noise etc., e.g. the number of machi-
nes and other neighboring operations. Reliable
workplace values may also vary from country to
country. With this information the user should at
least be able to make a better assessment of the
dangers and risks involved.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
-1
•
Have the appliance serviced whenever ne-
-1
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
- 18 -
06.07.2018 10:29:29 06.07.2018 10:29:29