CIAT coadis 235/11 Notice D'utilisation page 13

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 1
U
NIT SERVICING
A periodic servicing between each cooling and
heating seasons is to schedule, particularly for
elements
favourable to dirtying : filte, drain
pan, coil, condensate pump ...
Before removing the body and performing any
intervention inside the unit, switch off unit by
switching off the electricity supply.
AIR FILTER SERVICING
– Insert the supplied key inside the grille support
notch. Orientate the key near outside of the unit
to unclip the support. (11a)
– Once uncliped the both supports, the grille can
stay hooked to the panel
– The filter by choice can be removed by the front
or the rear (11b). Two security points can be
uncatched to facilitate the operation.
The filter is indispensable for correct operation; if its
operation is degraded, the exchanger coil can
become clogged.
We preconise its exchange between each working
season. In case of a monthly servicing schedule the
filter should be cleaned by vacuuming in the
opposite direction to the air flow.
The
interval
between
considerably depending upon the nature of the
room and installation conditions.
WATER COIL SERVICING
The clean state of the coil is a positive factor for
proper output of the unit :
- Disconnect the water coil, and the drain pan
piping.
- Take down the coil and the drain pan by
unscrewing the 4 screws (fig.8c), and slide the
complete element to the outside.
- The coil can be cleaned with a vacuum cleaner.
FAN ASSEMBLY SERVICING
Fan assembly dismounting principle (fig.12) :
After the inlet grille removed (see filter servicing),
disconnect the wiring block after the unit is switched
off.
Unscrew and remove only 2 or 3 screws (fig.12a).
Pull down the fan assembly to set free from the 2 or
3 others attachments screws.
Take out the fan assembly by the inlet grille section.
Carry out the operation in reverse order to remount
the fan assembly.
Periodically, check the cleaning of fans and motor,
if necessary, clean them by help of a vaccuum
cleaner taking care not to cause damage.
Electric motor do not require particular servicing.
(
.11)
FIG
cleanings
can
vary
DRAIN PAN SERVICING
The drain pan without water retention must stay
clean. A complete cleaning of the plastic drain pan
and its nuts may be done with a non abrasive lightly
soaped liquid. This cleaning can be done by outside
the unit, or after removing of the complete drain pan
(see Coil Servicing).
AIR DIFFUSION PANEL SERVICING
To maintain the aesthetic appearance of the
appliance, wipe with a lightly soaped damp sponge,
then polish with a soft, dry cloth. Never use
abrasive products.
SPARE PARTS LIST
a : Air filter
b : Complete fan assembly
c : Electric motor
d : Alumium fan
eg : 2 left-pipe coil ed : 2 right-pipe coil
fg : 4 left-pipe coil fd : 4 right-pipe coil
g : monotube electric element
h+l : Insulated panel without filter/inlet grille, with
nozzles
i : Manual reset temperature limiter
j : Punched inlet painted steel grille
k : Plastic grille supports
l : Air diffusion nozzle
m : Fliter access and nozzles orientating key
GUARANTEE
All of our units are tested and approved before
shipping.
The guarantee covers manufacturing faults ; but we
cannot be held responsible for corrosion damage.
Motors
are
not
connecting, poor protection or use without an air
filter.
Our guarantee coincides with that of the motor
supplier. The installer should never tamper with the
motor. If this occurs, any possible guarantee
benefits are lost.
CIAT complies with the CE mark, authorising the
free circulation of its units throughout the European
Union. This mark is a guarantee of personal safety
and protection.
6
(F
.17)
IG
&
TESTS
guaranteed
against
faulty

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Coadis 235/22Coadis 235/33

Table des Matières