Tuner Setup; Setting Up Tv Channels; Using Auto Channel Preset; Setting For Skipping Unwanted Channels - Pioneer PDP-6010FD Mode D'emploi

Tuner Setup

Chapter 9
Tuner Setup

Setting up TV channels

This section describes how to search and set up TV channels that
you can watch under the current conditions. Unless you set up
TV channels using Auto Channel Preset, you may not be able to
tune in those channels.

Using Auto Channel Preset

Auto Channel Preset automatically searches and sets up TV
channels.
1
Press HOME MENU.
2
Select "Tuner Setup" ( /
3
Select "Channel Setup" ( /
4
Select "Ant. A" or "Ant. B" ( /
5
Select "Auto Channel Preset" ( /
6
Select "Air" or "Cable" ( /
Channel Setup
Ant. A Auto Ch. Preset
Air
Ant. A Auto Channel Preset
Cable
Enter Begin Preset
• Channel search automatically starts.
Channel Setup Ant. A Auto Ch. Preset
Ant. A Auto Channel Preset • Cable
D Cancel
• To quit Auto Channel Preset halfway, press D.
7
After Auto Channel Preset has been finished, press
HOME MENU to exit the menu.
Note
• When using the Cable Converter, you may need to manually
add Cable Converter output channels.
• When an inserted CableCARD™ is functioning, you can
execute Auto Channel Preset by selecting "Ant.B" in step 4.

Setting for skipping unwanted channels

From among TV channels searched and set up using Auto
Channel Preset, you can select channels to be skipped when
CH+/– are operated.
1
Press HOME MENU.
2
Select "Tuner Setup" ( /
3
Select "Channel Setup" ( /
4
Select "Ant. A" or "Ant. B" ( /
5
Select "Channel Keep/Skip" ( /
then ENTER).
then ENTER).
then ENTER).
then ENTER).
then ENTER).
Cable
xxxxxxxxxxxxxxxxxxxxx
2.0
xxxxxxxxxxxxxxxxxxxxx
4.0 xxxxxxxxxxxxxxxxxxxxx
6.0
Cancel Home Menu Exit
D
Cable
xxxxxxxxxxxxxxxx
One Moment Please ...
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
Home Menu
Exit
then ENTER).
then ENTER).
then ENTER).
then ENTER).
6
Select a channel to be skipped ( /
Channel Setup Ant. A
Channel Keep/Skip
Ant. A Channel Keep/Skip
• For the skipped channel, a check mark disappears.
7
Press HOME MENU to exit the menu.
Note
• To restore skipped channels, use the above procedure except
that you select a skipped channel in step 6.
• When using the Cable Converter, you may need to manually
add Cable Converter output channels.

Setting up TV channels manually

This section describes how to manually set up TV channels that
have not been set up by Auto Channel Preset.
1
Press HOME MENU.
2
Select "Tuner Setup" ( /
3
Select "Channel Setup" ( /
4
Select "Ant. A" or "Ant. B" ( /
5
Select "Add Channel" ( /
6
Select a channel number to be added ( /
• You can also use buttons 0 to 9 to enter a channel number.
Channel Setup Ant. A Add Channel
Ant. A Add Channel
000
1
• After ENTER has been pressed, a confirmation screen
appears.
7
Press A to complete the setup process.
8
Press HOME MENU to exit the menu.
Note
• Adding channels manually is for adding analog channels only.
Digital channels cannot be added.

Checking signal strength

When you have selected antenna A, you can check the current
channel's signal strength. You may use this function when
receiving a channel through a VHF/UHF antenna.
1
Press HOME MENU.
2
Select "Tuner Setup" ( /
3
Select "Channel Setup" ( /
4
Select "Ant. A" ( / then ENTER).
then ENTER).
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
2.0
xxxxxxxxxxxxxxxxxxxxx
4.0
6.0
Home Menu Exit
then ENTER).
then ENTER).
then ENTER).
then ENTER).
then ENTER).
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit
then ENTER).
then ENTER).
09
43
En