Operating Times - Wolf Garten Premio 40 EAKF Mode D'emploi

Safety Instructions
• as a tractor (for drive mowers) for lawn turning devices, strewing car, trailer e.g. for passengers transporting cuttings (except in the grass collection
basket provided).
• Never let children or other persons who are not familiar with the operating instructions use the lawnmower. Juveniles under l6 years may not use the
equipment. Local regulations may specify the minimum age of the operator.
• Never cut your lawn if persons, particularly children and animals are in the vicinity.
• Mow only in daylight or with appropriate artificial lighting.
2. Before Mowing:
• Never mow without wearing firm footwear and long trousers: Never mow barefoot or in open sandals.
• ttach the baffle provided and/or collection gear. Make certain that it is firmly fitted. Operation without or with damaged protective equipment is forbidden.
• Examine the cable installed externally on the mower and the connecting cable for damage and ageing (perishing). Use only when in good condition.
• Check the work tool to make certain that the mounting elements are tightly fitted for damage or serious wear.
• Observe the installation instructions when replacing parts.
• Inspect the catcher bag frequently for wear and deformation.
• Check the condition of all outside cables. geing and damaged cables must be replaced by a qualified person.
• Before adjusting or cleaning the tool and before checking for a caught or damaged connecting cable, switch off the tool and disconnect the mains plug.
• Before using, ensure (visually) that the cutting blades and their attaching parts are not blunt or damaged. Replace blunt or damaged cutting blades
by whole sets to avoid imbalance.
3. Cable
• Please work with safety cables from WOLF. For the connection only lines which are not lighter than rubber hose lines H0 7 RN-F to DIN/VDE 0282
with a minimum diameter of 3 x 1,5 mm
• ttachments must be splashproof (applicable in ustria only).
• Use a leakage-protective system (RCD) with a leakage current of no more than 30 m .
• ttach connection cable to traction relief. Make sure that in does not rub against edges, pointed or sharp objects. Do not squeeze cable through
door or window gaps.
• Switching devices must not be removed or bridged (e.g. tying of switching lever to guide spar).
4. Starting the Motor:
• Switch om motor only when your feet are at a safe distanca from the mower chassis and when standing on firm ground - not in high grass;
• Do not tilt the mower when starting the motor unless the mower must be tilted for starting. If so, do not tilt the mower more than absolutely necessary and
lift only the part farthest from the user. lways ensure that both of your hands are in the working positions before replacing the mower on the ground.
• Do not start the engine if you are standing in front of the ejection channel.
5. During work - for your Safety:
• TTENTION - D NGER! Keep hands away from rotating cutter blade and remember that the blade continues to rotate for a short while after the
motor has been switched off;
• lways walk behind the handle bars, holding the upper handle grip with both hands;
• Keep feet away from the mower chassis and be extra carefull when mowing on hills or slopes to prevent slipping. Mow across the hill, if possible.
Mowe forward at walking pace, never run;
• void pulling the mower backwards (towards you) during work;
• Switch off motor before tilting or lifting the mower and when pushing off the lawn area;
• Never use the mower when the protective parts are damaged or safety equipment such as the deflector and/or grass catching parts are missing;
• Use the height adjustment only when the mower is stationary and the rotating blade has come to a complete standstill;
• Before removing the grassbox switch off the motor and wait until the rotating blade has come to a complete standstill;
• Never push mower over gravel with running motor;
• If possible, avoid mowing in wet coditions;
• Switch off motor and remove cable plug socket before working at the cutter blades, before making any adjustments, when cable has become entangled
a) before leaving the mower unattended,
b) before attempting to clear a blockade underneath chassis or at rear throe-out,
c) before inspecting, cleaning or working on the mower,
d) immediately after your mower blade has hit a foreign and hard object. Check the condition of the deck and cutter blade before switching on again,
e) immediately when your mower starts to vibrate strongly. Locate the reason for the vibration and remedy.
• If your mower has a power-drive do switch the power-drive off before starting motor or engine.
• Should the power cord be damaged during use, immediately disconnect it fromthe mains. Do not touch the cable until it has been disconnected from
the mains.
6. Maintenance:
• Switch off motor and remove mains plug before carrying out any repairs or maintenance to your mower;
• Do not clean yor mower with a hose pipe - and particularly not with a high-pressure spray;
• Inspect regularly all visible nuts and bolts - particularly ot the cutter blade - for their tightness;
• TTENTION! Sharpening and changing of cutter blades should be done by a qualified service centre because it is necessary that the correct
balance after fixing is guaranteed;
• Damaged and worn parts must always be replaced with original WOLF replacement parts as otherwise your guarantee will be invalidated;
• Your service centre should check your mower regularly and particularly after any hard obstacle hat hit the chassis and/or the cutter blades;
• Store your mower only in a dry room.
• If cutter blade hits a hard foreign object whilst mowing switch of motor immediately, remove safety key and check cutter blade carefully for damage.
Please observe these hints, as they help you to prevent damage or even accidents!
• Conduct maintenance and cleaning work only when the motor is switched off and the key has been removed.

Operating Times

ccording to law in some countries lawn mowing not allowed on Saturdays and Sundays and at certain other times (eg. at midday
or after 7 p.m.). Please check noise abatement regulations prevailing in your country.
ssembly
Fixing of handle and adjustment of height (fig. M1/M2)
TTENTION! Take care that the switch cable does not become caught and crused when folding the handle frame.
Fold down upper handle part M1 (1). Tighten handwheels for the handle attachment M1 (2). Turn brackets for the cable guide M2
(3) to the left or right until the entire handle rod M2 (4) can easily be folded backward; it must click into the right and left recess
M2 (5). Then set the desired body height and tighten handwheels M2 (6).
Folding of handle frame (fig. M2/M3)
TTENTION! Take cara that the switch cable does not become caught and crushed when folding the handle frame.
Turn brackets for the cable guide M2 (3) to the left or right. Loosen lower handwheels M3 (1) until the handle rod M3 (2) can be
pulled apart about 2 cm and folded forward slightly.
2 must be used.
10