Orion 25050 Manuel D'utilisation page 2

INTRODUCTION
WARNING
T
his uniT is inTended for professional use
r
ead all The insTrucTions in This manual prior To use
• Only use the unit for the purposes for which it is intended.
• This unit has not been approved for use in commercial transac-
tions.
• Do not alter or modify the unit.
• Do not exceed the maximum unit working pressure. See page 7,
technical specifications.
• Use the unit with fluids and solutions which are compatible with
INSTALLATION
The meter can be connected to a control gun or installed directly in
the distribution line pipe.
It is recommendable to install a cut-off valve before the meter to
facilitate its maintenance or repair.
The meter has a ½" NPSM connection at the inlet and outlet.
It also includes an inlet flange and a flange at the outlet with
BATTERIES
The location of the batteries is shown in the following figure:
CHARGING STATUS OF THE BATTERIES
The meter shows the charging status of the batteries on the display.
If the meter does not switch on when pressing the RESET button, or switches off after being pressed, replace the batteries with new ones.
Alentec & Orion AB Grustagsvägen 4, SE-13840, Älta, SWEDEN · info@alentec.se · www.alentec.com
2
.
BATTERIES OK
the moist parts of the unit. See the relevant section of the tech-
EN
nical specifications.
.
INTRODUCTION
• Observe the manufacturer's safety warnings for the fluids used.
• The meter has been manufactured with low tolerances in order to
WARNING: This unit is intended for professional use.
!
Read all the instructions in this manual prior to use.
ensure high precision over a wide range of flows and viscosity.
• Check measurement units counter before first use.
• The meter is an oval gear model.
• Only use the unit for the purposes for which it is intended.
• In order to save energy the meter switches off automatically
• This unit has not been approved for use in commercial
after 30 seconds of inactivity. All the data are stored for recovery
transactions.
• Do not alter or modify the unit.
once the meter has been restarted.
• Do not exceed the maximum unit working pressure.
See page 7, technical specifications.
• Use the unit with fluids and solutions which are
compatible with the moist parts of the unit. See the
relevant section of the technical specifications.
INSTALLATION
seating for an O-ring seal which enables connection for the range
of guns and original Orion accessories.
The meter can be connected to a control gun or installed
The meter requires two 1.5 V batteries and size LR 03 as the power directly in the distribution line pipe.
It is recommendable to install a cut-off valve before the
supply source. They are housed in a support which, in conjunction
meter to facilitate its maintenance or repair.
with the lid design, prevents the batteries from being removed The meter has a 1/2" BSP connection at the inlet and outlet.
It also includes an inlet flange and a flange at the outlet with
accidentally in the event of impacts or vibrations.
seating for an O-ring seal which enables connection for the
range of guns and original GARTEC accessories.
BATTERIES
The location of the batteries is shown in the following figure:
3
4
2
836 889 R. 12/18
GARTEC SRL · Castronno (VA) · Via Olona 4/A · Phone: +39 0332 895026 · Fax: +39 0332 895061 · Email: i
BATTERIES HALF CHARGED
1
2
BATTERIES EMPTY
REPLACE THE BATTERIES
• Observe the manufacturer's safety
fluids used.
• The meter has been manufactured w
in order to ensure high precision ove
flows and viscosity.
• Check measurement units counter be
• In order to save energy the meter switch
after 30 seconds of inactivity. All the
recovery once the meter has been rest
The meter requires two 1.5 V batteries an
power supply source. They are housed in
in conjunction with the lid design, pre
from being removed accidentally in the e
vibrations.
ATTENTION: The meter is supplied wit
mounted. Follow the procedure below
1. Loosen the screws (1) and remove th
cover (2).
2. Install the provided batteries (3) checki
matches the polarity symbols (4) mark
3. Put in place the cover (2) and tighten
WARNINGS
!
To guarantee the battery cov
that the battery is properly p
screws tightened.
When replacing the batteries the moni
1
the meter software version.
105088