Control Panel - Sony VPL-VW11HT Mode D'emploi

Control panel

0
LAMP/ TEMP/ POWER ON/
COVER FAN SAVING STANDBY
MENU PATTERN
ENTER RESET
9 8 7 6 5
1 I / 1 (on / standby) key
Turns the projector on and off when the projector is in
the standby mode. The ON/STANDBY indicator
lights in green when the power is turned on.
When turning off the power, press the I / 1 key
twice following the message on the screen, or press
and hold the key for about one second.
For details on steps for turning off the power, see "To turn
off the power" on page 20 (GB).
2 INPUT key
Selects the input signal. Each time you press the key,
the input signal switches as follows:
B VIDEO B S-VIDEO
INPUT-B b INPUT-A b
3 VIDEO MEMORY key
You can adjust the image in advance and store the
setting in the VIDEO MEMORY 1 to 6. You can
recall the setting by pressing this key. Pressing this
key selects memory numbers 1 through 6. When you
keep on pressing, it selects OFF, and then starts again
with 1. You can easily set, change, and view the
image in a suitable setting.
For more details on how to set the video memory, see the
VIDEO MEMORY of the INPUT SETTING menu on page
25 (GB).
4 LIGHT key
If you press this key while the power is on, the keys
on the control panel will be displayed in orange.
Press this key again to turn off the light.
The light will turn off automatically if no keys are
operated for 30 seconds.
5 PATTERN key
Displays the test pattern on the screen for focus
adjustment. Press again to clear the test pattern.
6 RESET key
Resets the value of an item back to its factory preset
value. This key functions when the menu or a setting
item is displayed on the screen.
1
2
INPUT
LIGHT
3
VIDEO MEMORY
4
Location and Function of Controls
7 ENTER key
Enters the settings of items in the menu system.
8 MENU key
Displays the on-screen menu. Press again to clear the
menu.
9 Arrow keys (M/m/</,)
Used to select the menu or to make various adjustments.
0 Indicators
LAMP/COVER: Lights up or flashes under the
following conditions:
• Lights up when the lamp has reached the end of
its life or the lamp does not turn on as a result
of high lamp temperature.
• Flashes when the lamp cover or air filter is not
secured firmly.
TEMP (Temperature)/FAN: Lights up or flashes
under the following conditions:
• Lights up when temperature inside the projector
becomes unusually high.
• Flashes when the fan is broken.
POWER SAVING: Lights up when the projector is
in the power saving mode. When POWER
SAVING in the SET SETTING menu is set to
ON, the projector goes into the power saving
mode if no signal is input or no keys are operated
for 10 minutes. Although the lamp goes out, the
cooling fan keeps running. In the power saving
mode, no key functions for the first 40 seconds.
The power saving mode is canceled when a signal
is input or any key is pressed.
ON/STANDBY: Lights up or flashes under the
following conditions:
• Lights in red when the AC power cord is
plugged into the wall outlet. Once in the
standby mode, you can turn on the projector
with the I / 1 key.
• Lights in green when the power is turned on.
• Flashes in green while the cooling fan runs after
turning off the power with the I / 1 key. The
fan runs for about 120 seconds after turning off
the power.
The ON/STANDBY indicator flashes quickly
for the first 40 seconds.
During this time, you cannot turn the power
back on with the I / 1 key.
For details on the LAMP/COVER and the TEMP/FAN
indicators, see page 37 (GB).
11
(GB)