Dust/Chip Extraction - Bosch PSS 300 AE Notice Originale

12 | English
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Self-generated dust extraction with dust box
(see figures C1–C4)
Place the dust box (3) onto the extraction outlet (7) until it
clicks into place.
To empty the dust box (3), pull the dust box downwards.
Before opening the dust box (3), knock the dust box against
a firm surface as shown in the figure to loosen the dust from
the filter element.
Take hold of the dust box (3) by the recessed grip, fold the
filter element (8) upwards out of the way and empty the dust
box. Use a soft brush to clean the flaps of the filter element
(8).
External dust extraction (see figure D)
Insert the dust extraction adapter (10) (accessory) into an
extraction hose (9) (accessory) until you hear it click into
place. Connect the dust extraction adapter (10) to the ex-
traction outlet (7) on the power tool and the extraction
hose (9) to a vacuum cleaner (accessory).
You will find an overview of connecting to various dust ex-
tractors at the end of these operating instructions.
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
In Germany, wood dust extraction requires extraction
devices which have been tested on the basis of TRGS 553;
self-generated dust extraction must not be used in the com-
mercial sector. Commercial operators must clarify the spe-
cific requirements for other materials with the responsible
trade association.
1 609 92A 691 | (22.04.2021)
Replacing the Sanding Sheet
Remove dirt and dust from the sanding plate (5), e.g. with a
brush, before attaching a new sanding sheet.
To ensure optimum dust extraction, make sure that the
punched holes in the sanding sheet are aligned with the
drilled holes in the sanding plate.
Sanding sheets with hook-and-loop backing
(see figure A)
The sanding plate (5) is fitted with a hook-and-loop fasten-
ing, allowing sanding sheets with a similar backing to be se-
cured quickly and easily.
Tap the hook-and-loop fastening of the sanding plate (5) be-
fore fitting the sanding sheet (6) to facilitate maximum adhe-
sion.
Position the sanding sheet (6) so that it is flush with one side
of the sanding plate (5), then place the sanding sheet on the
sanding plate and press it on firmly.
To remove the sanding sheet (6), take hold of it by a corner
and pull it away from the sanding plate (5).
Sanding sheets without hook-and-loop backing (see
figure B)
Gently lift and unhook the clamps (4).
Guide the sanding sheet (6) all the way under the opened
rear clamp (4) and firmly clamp the sanding sheet into place
by rehooking the clamp (4).
Position the sanding sheet (6) so that it fits tightly around
the sanding plate.
Guide the other end of the sanding sheet (6) under the front
clamp (4) and firmly clamp the sanding sheet into place by
rehooking the clamp (4).
Unperforated sanding sheets, e.g. from rolls or bulk stock
sold by the metre, can be perforated using the punch (11)
for the purpose of dust extraction. To do this, fit the sanding
sheet on the power tool and push the tool down onto the
punch (see figure E).
To remove the sanding sheet (6), undo the clamps (4) and
pull out the sanding sheet.
Selecting a sanding sheet
Different sanding sheets are available, depending on the ma-
terial you are working with and the required surface removal
rate:
For processing all wood and wood-based ma-
terials
For pre-sanding, e.g. of rough and un-
even beams and boards
For surface sanding and levelling of
slight irregularities
For finish-sanding and fine sanding of
hardwoods
Grit
40–240
Coarse 40, 60
Medium 80, 100,
120
Fine 180, 240
40–320
Bosch Power Tools