Removing/Inserting The Battery - Milwaukee SDS PLUS ONE KEY Manuel De L'utilisateur

SPECIFICATIONS
Cat. No. ..................................................... 2915-20
Volts.............................................................. 18 DC
Battery Type .................................................M18™
Charger Type................................................M18™
No Load RPM ................................................ 0 - 800
BPM ............................................................. 0 - 4600
Module/FCC ID ............................ BGM11S/QOQ11
Type ...........................................................SDS Plus
Capacities
Drill Only*
Steel ............................................................ 1/2"
Wood ........................................................ 1-1/8"
Rotary Hammer (Concrete)
Carbide Tipped Percussion Bit ................. 1-1/8"
Core Bit..................................................... 2-1/2"
Recommended Ambient
Operating Temperature ......................0°F to 125°F
*Requires chuck adapter kit Cat. No. 48-66-1370
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always lock the trigger or remove
WARNING
the battery pack any time the tool
is not in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always use a side
handle when using this tool. Always brace or
hold securely.
Adjusting the Side Handle Position
1. Loosen the side handle by unscrewing the side
handle grip until the side handle rotates freely.
2. Rotate the side handle to the desired position.
3. Tighten the side handle grip securely.
For use with the Dust Extractor
The Milwaukee Cat. No. 2915-DE Dust Extractor
plugs directly into the 1-1/8" SDS PLUS Rotary
Hammer. For Dust Extractor assembly and operation,
refer to your Dust Extractor manual.
Setting the Depth Gauge
1. Press in the clamping lever.
2. Slide the depth gauge rod backward or forward
until it is set for the desired depth.
NOTE: The drilling depth is the distance between
the tip of the bit and the tip of the depth gauge rod.
Drilling Depth
3. Release the clamping lever.
Installing Drill Bits and Chisels
NOTE: Only use accessories with SDS or SDS Plus
shanks.
Be sure that the shank of the bit is clean. Dirt particles
may cause the bit to line up improperly. Do not use
bits larger than the maximum recommended capacity
of the drill because gear damage or motor overload-
ing may result. For best performance, be sure that
the bit is properly sharpened and the shank is lightly
greased before use.
1. Insert the bit or chisel into the nose of the tool.
2. Rotate bit slowly until it aligns with the locking
mechanism.
3. Push bit into tool until it locks.
4. Check that the bit is locked properly; it should
be possible to pull the bit back and forth slightly
(about 1/4").
5. To remove bits and chisels, pull bit holder release
collar toward the rear of tool and remove bit.
WARNING! Do not touch the drill bits or chisels
with bare hands immediately after drilling; they
may be hot and could burn skin.
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store or
Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
4