Status Indicators - KitchenAid KUDP01IL Guide D'utilisation Et D'entretien

SANI RINSE™ Option
Select this option to raise the water temperature in the final rinse
to approximately 160°F (70°C). The SANI RINSE™ Option adds
heat and time to the cycle. This high temperature rinse sanitizes
your dishes and glassware in accordance with NSF/ANSI
Standard 184 for Residential Dishwashers. Certified residential
dishwashers are not intended for licensed food establishments.
NOTE: SANI RINSE™ is an option with the Heavy and Normal
cycles. Only these sanitization cycles have been designed to
meet the NSF/ANSI requirements.
ENERGY SAVER™ Dry System
Select this option to dry dishes without heat. ENERGY SAVER™
Dry System is useful if you do dishes at night and unload in the
morning.
The dishes take longer to dry, and some spotting can occur. For
best drying, always use a liquid rinse aid. Some items (such as
plastics) may need towel drying.
NOTE: Rinse Only automatically uses this option. ENERGY
SAVER™ Dry System is an option with all other cycles.
Control Lock
Use Control Lock to prevent unintended use of the dishwasher.
You can also use the Control Lock feature to prevent unintended
cycle or option changes during a cycle.
When Control Lock is lit, all buttons are disabled.
NOTES:
The dishwasher door can be opened while the controls are
locked.
You can turn on the Lock while the dishwasher is running.
To turn on the Lock
Press and hold
for 4 seconds. Control Lock glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
To turn off the Lock
Press and hold ENERGY SAVER™ Dry control for 4 seconds. The
light turns off.
Delay Hours
Select this option to run your dishwasher at a later time or during
off-peak hours.
To delay the start
1. Close the door.
2. Select a wash cycle and options.
Press DELAY HOURS 1 time for a 2-hour delay, 2 times for a
4-hour delay, or 3 times for an 8-hour delay start.
The number glows above Delay Hours. The dishwasher starts
the cycle in the selected number of hours.
3. Press START. The selected cycle and option lights will flash
once to tell you that the delay has started.
NOTE: To cancel the delay, press DELAY HOURS until no number
is lit.
IMPORTANT:
Operate your dishwasher only when you are at home.
If your home is equipped with a water softener, do not start
the dishwasher during the regeneration of the softener.

Status Indicators

Follow the progress of your dishwasher with the Status
indicators.
Sensing/Soak
Your dishwasher senses the soil level on the dishes. Soil level
determines the length of some cycles, the amount of heat or
water added, and the cycle needed for the load. Soaks help
loosen soils on the dishes.
Sensing/Soak glows during the sensing and soak parts of the
cycle. Wash action continues while sensing occurs. Wash action
pauses during a soak.
Add a Dish
After a cycle starts, you can add an item to your dishwasher while
Add a Dish glows. After the light turns off, items added to the
dishwasher may not be completely cleaned.
Water Heating
Water Heating glows, and the cycle progression pauses,
whenever water is heated to a set temperature during a cycle.
Wash or rinse action continues as the water heats.
Clean
Clean glows when a cycle is finished. The light turns off when you
open and close the door or press Cancel.
Sanitized
If you select the SANI RINSE™ option, Sanitized glows when the
SANI RINSE™ cycle is finished. If your dishwasher did not
properly sanitize your dishes, the light flashes at the end of the
cycle. This can happen if the cycle is interrupted or the incoming
water temperature is too low. The light goes off when you open
and close the door.
13