Ec Declaration Of Conformity - Milwaukee M18 FQID Notice Originale

Do not dispose of used battery packs in the household refuse or by burning
them. Milwaukee Distributors offer to retrieve old batteries to protect our
environment.
Do not store the battery pack together with metal objects (short circuit risk).
Use only System M18 chargers for charging System M18 battery packs. Do
not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms.
Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it off
immediately with soap and water. In case of eye contact rinse thoroughly for
at least 10 minutes and immediately seek medical attention.
SPECIFIED CONDITIONS OF USE
The cordless impact wrench can be used to tighten and loosen nuts and
bolts wherever no mains connection is available.
Do not use this product in any other way as stated for normal use.
RPM SETTING
The function is designed to reduce screw stripping, screw breakage,
and damage to the work surface when driving self-tapping screws. This
function is optimized for the most common materials, including #8-#10
self-tapping screws between 12-25 mm length and 0,5-1 mm sheet metal.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described under
"Technical Data" fulfi lls all the relevant regulations and the directives
2011/65/EU (RoHs), 2014/30/EU, 2006/42/EC, and the following harmonized
standards have been used:
EN 62841-1:2015
EN 62841-2-2:2014
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015
EN 50581:2012
Winnenden, 2016-05-30
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time should be recharged
before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the
battery pack. Avoid extended exposure to heat or sunshine (risk of
overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be fully
charged.
To obtain the longest possible battery life remove the battery pack from the
charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from
moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that
cause high current draw, the tool will vibrate for about 2 seconds and then
the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the battery could
become to high. If this happens, the battery will shut down.
Place the battery on the charger to charge and reset it.
414 833 - M18FQID.indd 17 414 833 - M18FQID.indd 17
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to
Dangerous Goods regulations. Transport preparation and transport are
exclusively to be carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
Use only Milwaukee accessories and spare parts. Should components need
to be replaced which have not been described, please contact one of our
Milwaukee service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
machine type printed as well as the six-digit No. on the label and order the
drawing at your local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the
machine.
Please read the instructions carefully before starting the
machine.
Do not dispose of electric tools together with household waste
material.
Electric tools and electronic equipment that have reached the
end of their life must be collected separately and returned to
an environmentally compatible recycling facility.
Check with your local authority or retailer for recycling advice
and collection point.
European Conformity Mark
National mark of conformity Ukraine
EurAsian Conformity Mark.
ENGLISH 17
02.01.2017 18:08:57 02.01.2017 18:08:57