Homelite 26CS Manuel D'utilisation page 11

Taille-bordures à ligne 26 cc
Masquer les pouces Voir aussi pour 26CS:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

FUELINg AND REFUELINg THE TRIMMER
FUEL MIXTURE
This product is powered by a 2-cycle engine and requires
premixing gasoline and 2-cycle oil. The mixture should be
at a 50:1 ratio.
NOTE: We recommend you use ONLY Homelite lubricant
in your product.
TO MIX THE FUEL:
 Use a clean container that is approved for use with
gasoline.
 Mix the 2-cycle engine oil with unleaded gasoline in the
container, according to the instructions on the oil
package.
This engine is certified to operate on unleaded gasoline
intended for automotive use with an octane rating of 87
[(R + M) / 2] or higher. Do not use automotive oil or 2-cycle
outboard oil.
NOTE: Most fuel mixture will stay fresh up to 30 days. DO
NOT mix quantities larger than usable in a 30 day period.
PREMIUM EXACT MIX (50:1)
gASOLINE
1 gallon (US)
1 liter
OXYgENATED FUELS
DO NOT USE E85 FUEL. IT WILL VOID YOUR
WARRANTY.
NOTE: Fuel system damage or performance problems re-
sulting from the use of an oxygenated fuel containing more
than the percentages of oxygenates stated previously are
not covered under warranty.
Ethanol. Gasoline containing up to 10% ethanol by vol-
ume (commonly referred to as E10) or 15% ethanol by
volume (commonly referred to as E15) are acceptable.
Do not use E85 fuel.
FILLINg TANK
 Clean surface around fuel cap to prevent contamination.
 Set trimmer on its side so that the spout points up.
 Loosen fuel cap slowly. Rest the cap on a clean surface.
 Carefully pour fuel into the tank. Avoid spillage.
 Immediately replace fuel cap and hand tighten. Wipe up
any fuel spillage.
NOTE: It is normal for smoke to be emitted from a new
engine after first use.
OPERATION
Always shut off engine before fueling. Never add fuel to a
machine with a running or hot engine. Move at least 30 ft.
from refueling site before starting engine. Do not smoke
and stay away from open flames and sparks. Failure to
safely handle fuel could result in serious personal injury.
STARTINg AND STOPPINg
See Figures 7 - 8.
Trimmer should be on a flat, bare surface for starting.
To start a cold engine:
 Slowly press the primer bulb 10 times.
 Set the choke lever to the FULL CHOKE position.
 Squeeze the throttle trigger fully and pull starter handle
LUbRICANT
 Set the choke lever to the HALF CHOKE position.
2.6 oz.
 Pull the starter grip until the engine runs. Do not pull the
20 cc (20 ml)
 Allow the engine to run for 10 seconds, then set the choke
To restart a warm engine:
 Slowly press the primer bulb 10 times.
 Set the choke lever to the RUN position.
 Squeeze the throttle trigger fully and pull the starter handle
To stop the engine:
 To stop the engine, depress the STOP switch to the stop
IF ASSISTANCE IS REqUIRED STARTINg THIS
PRODUCT:
Do not return this product to the retail store where it was
purchased. Please call our Customer Service Department
for any issues you may have.
For Help Call: 1-800-242-4672
Page 7 — English
WARNINg:
NOTE: After the 7th press, fuel should be visible in the
primer bulb. If it is not, continue to press the primer until
you see fuel in the bulb.
sharply until engine attempts to run. Do not pull the starter
handle more than four (4) times.
NOTE: Keep throttle trigger squeezed fully.
starter grip more than six (6) times.
NOTE: If the engine does not start, return to the full choke
position and repeat the steps that follow.
lever to the RUN position.
until the engine runs.
position "
".

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

26ssUt32600Ut32650

Table des Matières