EMAK PW 121C Manuel D'utilisation Et D'entretien page 18

2 f
eatures and
ELECTRICAL CONNECTION
Mains power supply
Absorbed power
Fuse
HYDRAULIC CONNECTION
Maximum inlet water temperature
Minimum inlet water temperature
Minimum inlet water flow
Maximum inlet water pressure
Maximum priming depth
PERFORMANCE
Water flow
Maximum pressure
Recoil of cleaner gun
Sound level
Operator arm vibrations
WEIGHT AND DIMENSION
Lenght x width x height
Weight
Detergent bottle capacity
All features and technical specifications are only indications. The Manufacturer reserves the right to modify the appliance as it deems necessary.
2.1 I
dentIfICatIon
Please also refer to figures 1 to 2, which are located at the start of these operating and maintenance instructions.
1 Electric power cord
2 Main switch
3 Handling bar
4 Housing for water gun / lance hose
5 Warning notice
6 Hose reel
7 Identification plate
8 Water outlet connector
9 Housing for foaming lance
10 Lifting handle
11 Securfix ring nut
12 Water inlet quick-fit connector
13 Housing for electric power cord
14 Water gun
2.2 s d
afety evICes
This water cleaner is provided with the following safety devices:
a) thermal protector
It's a device that stops the water cleaner operation in case of motor overheating.
In this case, proceed as follows:
• switch the main switch (2) to position "0" and remove the plug from the power outlet;
• press the lever (26) on the cleaner gun to eliminate any remaining pressure;
• wait 10 to 15 minutes until the water cleaner cools down;
• check that the instructions in the "
section have been followed, particularly regarding any extension cord used;
• replace the electric plug in the power outlet and repeat the start-up procedure described in the "
section.
18
t s
eChnICal peCIfICatIons
PW 121C - IP 1210S
450 l/h / 120 US gph
0,8 MPa / 8 bar / 116 psi
360 l/h / 95 US gph
13 MPa / 130 bars / 1885 psi
C
of omponents
CHECKS AND CONNECTION TO THE MAINS ELECTRICITY SUPPLY
PW 136C - IP 1360S
230 V / 1~50 Hz
1,7 kW
16 A
40 °C / 98 °F
5 °C / 41 °F
500 l/h / 132 US gph
0,8 MPa / 8 bar / 116 psi
0 m / 0 ft
410 l/h / 108 US gph
14 MPa / 140 bars / 2031 psi
11 N
76,2 dB (A)
0,73 m/s 2
310 x 308 x 820 mm / 12 x 12 x 32 in
12 kg / 26 lb
0,35 l / 0,09 US gal
17 Nozzle cleaning pin
18 Rotojet rotating nozzle head (PW 136C - PW 145C IP 1360S -
IP 1450S only)
19 Foaming lance
20 Detergent intake adjuster
21 Opening for detergent
22 Water brush (PW 136C - PW 145C IP 1360S - IP 1450S only)
23 High pressure hose
24 Quick fit connector for high-pressure hose
25 Safety catch on water gun lever
26 Water gun lever
27 Nozzle support head
28 Lance hose
PW 145C - IP 1450S
230 V / 1~50 Hz
2,0 kW
16 A
40 °C / 98 °F
5 °C / 41 °F
600 l/h / 159 US gph
0,8 MPa / 8 bar / 116 psi
0 m / 0 ft
480 l/h / 127 US gph
15 MPa / 150 bars / 2175 psi
14 N
77,3 dB (A)
1,31 m/s
2
13 kg / 29 lb
230 V / 1~50 Hz
2,3 kW
16 A
40 °C / 98 °F
5 °C / 41 °F
0 m / 0 ft
15 N
77,3 dB (A)
1,31 m/s
2
13 kg / 29 lb
"
OPERATION "