Replacement Parts; Use Proper Extension Cord - Hitachi C 10FCG Mode D'emploi

English
5. Always handle the POWER TOOL carefully. If the POWER TOOL falls or
strikes against a hard object, it might become deformed or cracked or
sustain other damage.
6. Always cease operating the saw at once, if you notice any abnormality
whatsoever.
7. Always confi rm that all components are mounted properly and securely
before using the tool.
8. When replacing the saw blade, always confi rm that the rpm rating of the
new blade is correct for use on this tool.
9. Always shut off the power and wait for the saw blade to completely stop
rotating before doing any maintenance or adjustments.
10. Always clamp or otherwise secure the workpiece to the fence; otherwise
the workpiece might be thrust from the table and cause bodily harm.
11. During miter or bevel cutting, always wait for the rotation of the blade to
stop completely before lifting the saw blade.
12. Always make a trial run fi rst before attempting any new use of the saw.
13. Always handle the saw blade with care when dismounting and mounting
it.
14. Always confi rm that the workpiece is free of nails or other foreign objects
before beginning a cut.
15. Always keep your hands out of the path of the saw blade.
16. Always confi rm that the lower guard is in the proper place before using
the saw.
17. Inspect the tool power cords periodically.
18. Always confi rm that the proper lengths and types of extension cords are
being utilized, if necessary, before starting the tool.
19. Always confi rm that the motor air vents are fully open before using the
tool.
20. Always wait until the motor has reached full speed before starting a cut.
21. Always keep the handles dry, clean and free of oil and grease. Hold the
tool fi rmly when in use.
22. Always use outboard stands to provide support for long workpieces that
overhang the table of the compound miter saw.
23. Always operate the tool after ensuring the workpiece is fi xed properly
with a vise assembly.
24. The operating instructions provided with the tool shall direct the user to
secure the tool to supporting structure if, during normal operation, there is
a tendency for the tool to tip over, slide, or walk on the supporting surface.
DON'Ts
NEVER VIOLATE THE FOLLOWING RULES TO ASSURE
SAFE USE OF THIS TOOL:
1. Never operate the POWER TOOL unless you fully understand the
operating instructions contained in this Manual.
2. Never leave the POWER TOOL unattended without fi rst unplugging the
power cord.
3. Never operate the POWER TOOL when you are tired, after you have
taken any medications, or have consumed any alcoholic beverages.
4. Never use the POWER TOOL for applications not specified in the
instruction manual.

USE PROPER EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
Ampere Rating
More Not More
Than Than
0 – 6
6 – 10
10 – 12
12 – 16
WARNING:
Avoid electrical shock hazard. Never use this tool with a damaged or frayed electrical cord or extension cord.
Inspect all electrical cords regularly. Never use in or near water or in any environment where electric shock is possible.
4
5. Never operate the tool while wearing loose clothing, a necktie or jewelry,
or while your hair is uncovered, to protect against getting caught in the
moving machinery.
6. Never reach around the saw blade.
7. Never touch any moving parts, including the blade, while the saw is in use.
8. Never remove any safety devices or blade guards; use of the tool without
them would be hazardous.
9. Never lock the lower guard; always confi rm that it slides smoothly before
using the tool.
10. Never damage the power cord of the tool.
11. Never attempt to move a plugged-in POWER TOOL while your fi nger is
on the starting switch.
12. Never use the POWER TOOL if the starting switch does not turn on and
off properly.
13. Never use the POWER TOOL if the plastic housing or the handle is
cracked or deformed.
14. Never use the POWER TOOL near fl ammable liquids or gases because
sparking can cause an explosion.
15. Never clean plastic components with solvents because the plastic may
dissolve.
16. Never operate the saw unless all the lower guards are in place.
17. Never raise the saw blade from the workpiece until it has fi rst come to a
complete stop.
18. Never place your limbs inside of the line next to warning sign " " while
the tool is being operated. This may cause hazardous conditions.
19. Never use abrasive type blades on this saw.
20. Never expose to rain or use in damp locations.
21. Never cut ferrous metals or masonry.
WARNING:
FOR YOUR OWN SAFETY READ THIS INSTRUCTION
MANUAL BEFORE OPERATING THE COMPOUND
MITER SAW
1. Always wear eye protection when using the compound miter saw.
2. Always keep hands out of the path of the saw blade.
3. Never operate the saw without the guards in place.
4. Never perform any freehand operation with the compound miter saw.
5. Never reach around the saw blade.
6. Always turn off tool and wait for saw blade to stop before moving workpiece
or changing settings.
7. Always disconnect power before changing blade or servicing.
8. Saw blade diameter is 10 in. (255mm).
9. No load speed is 5000/min.
10. To reduce the risk of injury, return carriage to the full rear position after
each crosscut operation.

REPLACEMENT PARTS

When servicing use only identical replacement parts.
Repairs should be conducted only by a Hitachi authorized service center.
MINIMUM GAGE FOR CORD SETS
Total Length of Cord in Feet (Meter)
0 – 25 26 – 50
(0 – 7.6) (7.9 – 15.2)
18 16
18 16
16 16
14 12
51 – 100
(15.5 – 30.5)
AWG
16
14
14
Not Recommended
101 – 150
(30.8 – 45.7)
14
12
12