Bosch GKS 18 V-LI Professional Notice Originale page 18

18 | English
Technical data
Hand-held circular saw
Article number
Rated voltage
No-load speed
Max. cutting depth
– at a 0° mitre/bevel angle
– at a 45° mitre/bevel angle
Spindle lock
Base plate dimensions
Max. saw blade diameter
Min. saw blade diameter
Max. base blade thickness
Min. base blade thickness
Max. tooth thickness/offset
Locating bore
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
B)
– during operation and
during storage
Recommended batteries
Recommended chargers
Recommended chargers for
inductive batteries
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-5.
Typically the A-weighted noise level of the power tool is:
Sound pressure level 86 dB(A); sound power level
97 dB(A). Uncertainty K = 3 dB.
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-5:
2
Sawing wood: a = 3 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
1 609 92A 4LJ | (20.12.2018)
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
GKS 18 V-LI
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
3 601 F6H 0..
power tool is used for other applications, with different ap-
V 18
plication tools or is poorly maintained, the vibration level
rpm 3900
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
mm 51
To estimate vibration and noise emissions accurately, the
mm 40
times when the tool is switched off or when it is running but
●
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
mm 146 x 272
over the total working period.
mm 165
Implement additional safety measures to protect the oper-
mm 160
ator from the effects of vibration, such as servicing the
mm 1.7
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
mm 1.0
mm 2.6
Fitting
mm 20
A)
kg 3.4–4.1 u
°C 0 to +45
Charging the Battery
°C -20 to +50
u
GBA 18V..
Note: The battery is supplied partially charged. To ensure
GBA 18V... W
full battery capacity, fully charge the battery in the charger
AL 1814 CV
before using your power tool for the first time.
AL 1820 CV
The lithium-ion battery can be charged at any time without
AL 1860 CV
reducing its service life. Interrupting the charging process
GAL 1880 CV
does not damage the battery.
GAL 18V-..
The lithium-ion battery is protected against deep discharge
GAL 3680 CV
by the "Electronic Cell Protection (ECP)". When the battery
GAX 18V-30
is discharged, the power tool is switched off by means of a
AL 3620 CV
protective circuit: The application tool no longer rotates.
GAL18.. W
u
Follow the instructions on correct disposal.
Removing the battery
The battery (3) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release button
(24) is pressed unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
To remove the battery (3), press the release button (24)
and pull the battery to the rear and out of the power tool. Do
not use force to do this.
Battery charge indicator (see figure F)
2
The three green LEDs of the battery charge indicator (32) in-
dicate the state of charge of the battery (3). For safety reas-
Only use saw blades the maximum permitted speed of
which is higher than the no-load speed of the power
tool.
Use only the chargers listed on the accessories page.
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Bosch Power Tools