Bosch GGS 7 Professional Notice Originale page 14

OBJ_BUCH-247-005.book Page 14 Thursday, May 19, 2011 11:03 AM
14 | English
Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent kickback
and loss of control over the power tool.
Additional safety instructions for grinding
Use only wheel types that are recommended for your
power tool and the specific guard designed for the se-
lected wheel. Wheels for which the power tool was not de-
signed cannot be adequately guarded and are unsafe.
Wheels must be used only for recommended applica-
tions. For example: do not grind with the side of the
cut-off wheel. Abrasive cut-off wheels are intended for
peripheral grinding; side forces applied to these wheels
may cause them to shatter.
Always use undamaged wheel flanges that are of cor-
rect size and shape for your selected wheel. Proper
wheel flanges support the wheel thus reducing the possi-
bility of wheel breakage. Flanges for cut-off wheels may be
different from grinding wheel flanges.
Do not use worn down wheels from larger power tools.
Wheels intended for larger power tools are not suitable for
the higher speed of a smaller tool and may burst.
Additional safety warnings
Wear safety goggles.
Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
Release the On/Off switch and set it to the off position
when the power supply is interrupted, e. g., in case of a
power failure or when the mains plug is pulled. This pre-
vents uncontrolled restarting.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Technical Data
Straight grinder
Article number
Rated power input
Output power
Rated speed
Speed control adjustment
Collet chuck diameter, max.
Spindle collar dia.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
3 609 929 B98 | (19.5.11)
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is designed for grinding and deburring metal us-
ing corundum grinding tools, as well as for working with sand-
ing wheels.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Collet chuck
2 Clamping nut
3 Grinder spindle
4 Spindle collar
5 On/Off switch
6 Thumbwheel for speed preselection
(GGS 7 C/GGS 27 LC)
7 Handle (insulated gripping surface)
8 Open-end spanner, size 17 mm*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
GGS 7 GGS 7 C
Professional Professional
0 601 212 0.. 0 601 212 7.. 0 601 215 0..
W 500
W 270
-1
min 7000 7000
-1
min – 3100 – 7000
mm 8
mm 35
GGS 27 L GGS 27 LC
Professional Professional
0 601 215 7..
600 500
360 300
27000 27000
– 12000 – 27000
8 8
35 35
Bosch Power Tools
600
360
8
35