Publicité
Les langues disponibles
Les langues disponibles
English
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated
battery packs.
Use of any other battery packs may create a risk
of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal
to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool
is maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach of
children and infirm persons.
PRECAUTIONS FOR CORDLESS IMPACT
DRIVER
1.
This is portable tool for tightening and loosenig
screws. Use it only for these operation.
2.
Use the earplugs if using for a long time.
3.
One-hand operation is extremely dangerous; hold
the unit firmly with both hands when operating.
4.
After installing the driver bit, pull lightly out the bit
to make sure that it does not come loose. If the bit is
not installed properly, it can come loose during
use, which can be dangerous.
5.
Use the bit that matches the screw.
6.
Tightening a screw with the impact driver at an
angle to that screw can damage the head of the
screw and the proper force will not be transmitted
to the screw. Tighten with this impact driver lined
up straight with the screw.
7.
Always charge the battery at a temperature of 0 –
40°C. Charging the battery at temperatures outside
the range of 0 – 40°C may prevent proper charging
and reduce battery life.
The most suitable temperature for charging is that
of 20 – 25°C.
8.
When one charging is completed, leave the charger
for about 15 minutes before the next charging of
battery.
Do not charge the battery more than 2 hours.
9.
Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
10. Never disassemble the rechargeable battery and
charger.
7
11. Never short-circuit the rechargeable battery. Short-
circuiting the battery will cause a great electric
current and overheat. It results in burn or damage
to the battery.
12. Do not dispose of the battery in fire.
If the battery is burnt, it may explode.
13. When drilling in wall, floor or ceiling, check for
buried electric power cord, etc.
14. Bring the battery to the shop from which it was
purchased as soon as the post-charging battery life
becomes too short for practical use. Do not dispose
of the exhausted battery.
15. Using an exhausted battery will damage the charger.
16. Do not insert object into the air ventilation slots of
the charger.
Inserting metal objects or inflammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
CAUTION ON LITHIUM-ION BATTERY
This battery is exclusively for the impact driver. Never
use with any other heavy-duty power tools (i.e. Circular
saw, Reciprocating saw, Disc grinder and Blower etc.).
To extend the lifetime, the lithium-ion battery equips
with the protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor
may stop. This is not the trouble but the result of
protection function.
1.
When the battery power remaining runs out, the
motor stops.
In such case, charge it up immediately.
2.
If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes
of overloading. After that, you can use it again.
3.
If the battery is overheated under overload work,
the battery power may stop.
In this case, stop using the battery and let the
battery cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand,
please be sure to heed the following precautions.
1.
Make sure that swarf and dust do not collect on the
battery.
During work make sure that swarf and dust do not
fall on the battery.
Make sure that any swarf and dust falling on the
power tool during work do not collect on the battery.
Do not store an unused battery in a location exposed
to swarf and dust.
Before storing a battery, remove any swarf and
dust that may adhere to it and do not store it together
with metal parts (screws, nails, etc.).
2.
Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or subject
the battery to severe physical shock.
3.
Do not use an apparently damaged or deformed
battery.
4.
Do not use the battery in reverse polarity.
5.
Do not connect directly to an electrical outlets or
car cigarette lighter sockets.
Publicité
