Apertura Manuale; General Safety - BFT LUX Instructions D'utilisation Et D'installation

APERTURA MANUALE

Versioni con blocco idraulico (LUXB-LUX2B)
Nei casi di emergenza, per esempio in mancanza di
energia elettrica, per sbloccare il cancello, infilare la
stessa chiave "C" usata per la regolazione delle val-
vole by-pass nel perno "P" triangolare situato sotto
l'attuatore (fig. 1) e ruotarla in senso antiorario. Il
cancello è così apribile manualmente imprimendo
una velocità di spinta uguale a quella di apertura
automatica.
Per ripristinare il funzionamento elettrico dell'attua-
tore, girare la chiave in senso orario fino al completo
bloccaggio del perno "P".
Versione senza blocco idraulico (LUX-LUXL-LUXG-
LUXGV)
É sufficiente aprire l'elettroserratura con la relativa
chiave e spingere manualmente l'anta.
DEMOLIZIONE
L'eliminazione dei materiali va fatta rispettan-
do le norme vigenti. Non gettate il vostro
apparecchio scartato, le pile o le batterie usate
nei rifiuti domestici. Avete la responsabilità di
restituire tutti i vostri rifiuti da apparecchia-
ture elettriche o elettroniche lasciandoli in
un punto di raccolta dedicato al loro riciclo.
Tutto quello che non è espressamente previsto
nel manuale d'uso, non è permesso. ll buon fun-
zionamento dell'operatore è garantito solo se ven-
gono rispettate le prescrizioni riportate in questo
manuale. La Ditta non risponde dei danni causati
dall'inosservanza delle indicazioni riportate in questo
manuale.
Lasciando inalterate le caratteristiche essenziali del
prodotto, la Ditta si riserva di apportare in qualunque
momento le modifiche che essa ritiene convenienti
per migliorare tecnicamente, costruttivamente e
commercialmente il prodotto, senza impegnarsi ad
aggiornare la presente pubblicazione.
USER WARNINGS (GB)
WARNING! Important safety instructions. Care-
fully read and comply with the Warnings and Ins-
tructions that come with the product as improper
use can cause injury to people and animals and
damage to property. Keep the instructions for fu-
ture reference and hand them on to any new users.
This product is meant to be used only for the
purpose for which it was explicitly installed.
Any other use constitutes improper use and,
consequently, is hazardous. The manufacturer
cannot be held liable for any damage as a result
of improper, incorrect or unreasonable use.

GENERAL SAFETY

Thank you for choosing this product. The Firm is
confident that its performance will meet your ope-
rating needs.
This product meets recognized technical standards
and complies with safety provisions when installed
correctly by qualified, expert personnel (professional
installer).
If installed and used correctly, the automated system
will meet operating safety standards. Nonetheless,
it is advisable to observe certain rules of behaviour
so that accidental problems can be avoided:
- Keep adults, children and property out of range of
the automated system, especially while it is moving.
- Do not allow children to play or stand within range
of the automated system.
- The unit can be used by children over 8 years old
and by people with reduced physical, sensory or
mental capabilities or with no experience or neces-
sary knowledge on condition they are supervised
or trained about the safe use of the equipment
and understand the risks involved. Children must
not play with the unit. Cleaning and maintenance
must not be performed by unsupervised children.
- Children must be supervised to ensure they do not
play with the device. Do not allow children to play
with the fixed controls. Keep remote controls out
of reach of children.
- Do not work near hinges or moving mechanical
parts.
- Do not hinder the leaf's movement and do not at-
tempt to open the door manually unless the actuator
has been released with the relevant release knob.
- Keep out of range of the motorized door or gate
while they are moving.
- Keep remote controls or other control devices out
of reach of children in order to avoid the automated
system being operated inadvertently.
- The manual release's activation could result in un-
controlled door movements if there are mechanical
faults or loss of balance.
- When using roller shutter openers: keep an eye
on the roller shutter while it is moving and keep
people away until it has closed completely. Exercise
care when activating the release, if such a device
is fitted, as an open shutter could drop quickly in
the event of wear or breakage.
- The breakage or wear of any mechanical parts of
the door (operated part), such as cables, springs,
supports, hinges, guides..., may generate a hazard.
Have the system checked by qualified, expert per-
sonnel (professional installer) at regular intervals
according to the instructions issued by the installer
or manufacturer of the door.
- When cleaning the outside, always cut off mains
power.
- Keep the photocells' optics and illuminating in-
dicator devices clean. Check that no branches or
shrubs interfere with the safety devices.
- Do not use the automated system if it is in need of
repair. In the event the automated system breaks
down or malfunctions, cut off mains power to the
system; do not attempt to repair or perform any
other work to rectify the fault yourself and instead
call in qualified, expert personnel (professional
installer) to perform the necessary repairs or main-
tenance. To allow access, activate the emergency
release (where fitted).
- If any part of the automated system requires direct
work of any kind that is not contemplated herein,
employ the services of qualified, expert personnel
(professional installer).
- At least once a year, have the automated system, and
especially all safety devices, checked by qualified,
expert personnel (professional installer) to make
sure that it is undamaged and working properly.
- A record must be made of any installation, main-
tenance and repair work and the relevant docu-
mentation kept and made available to the user on
request.
- Failure to comply with the above may result in
hazardous situations.
- Do not attempt to open the gate manually if:
- In mod. LUX-LUXL-LUXG-LUXGV the electric lock has
not been released by means of the appropriate key.
- In mod. LUXB-LUX2B the release has not been
activated by means of the appropriate key (fig.1).
- Do not modify the automation components.
- In case of malfunction, disconnect the power sup-
D811767_07
9
LUX -