Mitsubishi Electric PFAV-P250VM-E Manuel D'utilisation page 8

<Setting the Weekly Timer>
5 6
Shows the time setting Shows the selected operation (ON or OFF)
* Does not appear if operation is not set.
SUN
ON
°C
5. Press the appropriate Set Time button a as necessary to set the desired
time (at 5).
* As you hold the button down, the time first increments in minute intervals,
then in ten-minute intervals, and then in one-hour intervals.
6. Press the ON/OFF button 1 to select the desired operation (ON or OFF), at
6.
* Each press changes the next setting, in the following sequence: No display
(no setting) → "ON" → "OFF"
7. Press the appropriate Set Temperature button 3 to set the desired
temperature (at 7).
* Each press changes the setting, in the following sequence: No display (no
setting)
⇔ 24 ⇔ 25 ⇔ ... ⇔ 29 ⇔ 30 ⇔ 12 ⇔ ... ⇔ 23 ⇔ No display.
(Available range: The range for the setting is 12 °C to 30 °C. The actual
range over which the temperature can be controlled, however, will vary
according to the type of the connected unit.)
8. After making the appropriate settings at Steps 5, 6 and 7, press the Filter
button 4 to lock in the values.
To clear the currently set values for the selected operation, press and quickly
release the Check (Clear) button 0 once.
* The displayed time setting will change to "—:—", and the On/Off and
temperature settings will all disappear.
(To clear all weekly timer settings at once, hold down the Check (Clear)
button 0 for two seconds or more. The display will begin flashing,
indicating that all settings have been cleared.)
Note:
Your new entries will be cancelled if you press the Mode (Return) button 2
before pressing the Filter button 4.
If you have set two or more different operations for exactly the same time, only
the operation with the highest Operation No. will be carried out.
9. Repeat Steps 3 to 8 as necessary to fill as many of the available cells as you
wish.
10. Press the mode (Return) button 2 to return to the standard control screen
and complete the setting procedure.
11. To activate the timer, press the Timer On/Off button 9, so that the "TIMER
MODE OFF" indication disappears from the screen. Be sure that the
"TIMER MODE OFF" indication is no longer displayed.
* If there are no timer settings, the "TIMER MODE OFF" indication will flash
on the screen.
<How to View the Weekly Timer Settings>
8
TIMER
1. Be sure that the weekly timer indicator is visible on the screen (at 1).
2. Press the Timer Menu button b so that "TIMER MONITOR" is indicated on
the screen (at 8).
3. Press the Timer On/Off (Set Day) button 9 as necessary to select the day
you wish to view.
4. Press the or Operation button (7 or 8) as necessary to change the
timer operation shown on the display (at 9).
* Each press will advance to the next timer operation, in order of time setting.
5. To close the monitor and return to the standard control screen, press the
Mode (Return) button 2.
<To Turn Off the Weekly Timer>
Press the Timer On/Off button 9 so that "TIMER MODE OFF" appears at 0.
TIME SUN
°C
0
<To Turn On the Weekly Timer>
Press the Timer On/Off button 9 so that the "TIMER MODE OFF" indication (at
0) goes dark.
TIME SUN
°C
0
8
7
Shows the temperature setting
WEEKLY
* Does not appear if temperature is
not set.
9 Timer Settings
SUN
ON
OFF
°C
1
WEEKLY
°C
WEEKLY
°C
WEEKLY
2 Using the Simple Timer
You can set the simple timer in any of three ways.
• Start time only: The air conditioner starts when the set time has elapsed.
• Stop time only: The air conditioner stops when the set time has elapsed.
• Start & stop times: The air conditioner starts and stops at the respective
elapsed times.
The simple timer (start and stop) can be set only once within a 72-hour period.
The time setting is made in hour increments.
Note:
*1 Weekly Timer/Simple Timer/Auto Off Timer cannot be used at the same time.
*2 The simple timer will not operate when any of the following conditions is in
effect.
The timer is off; the system is in malfunction state; a test run is in progress; the
remote controller is undergoing self-check or remote controller check; the user
is in the process of selecting a function; the user is in the process of setting the
timer; the system is under central control. (Under these conditions, On/Off
operation is prohibited.)
TEMP.
MENU ON/OFF
BACK MONITOR/SET DAY
PAR-21MAA CLOCK
2 a 9
<How to Set the Simple Timer>
2 4
Timer Setting
Hr ON
AFTER
1. Be sure that you are at a standard control screen, and that the simple timer
indicator is visible in the display (at 1).
When something other than the Simple Timer is displayed, set it to SIMPLE
TIMER using the function selection of remote controller (see 3.4., [4]–3 (3))
timer function setting.
2. Press the Timer Menu button b, so that the Set-Up screen appears. (Note
that each press of the button toggles the display between Set-Up and TIMER
MONITOR.)
3. Press the ON/OFF button 1 to display the current ON or OFF simple timer
setting. Press the button once to display the time remaining to ON, and then
again to display the time remaining to OFF. (The ON/OFF indication appears
at 3).
• "ON" timer: The air conditioner will start operation when the specified
number of hours has elapsed.
• "OFF" timer:The air conditioner will stop operation when the specified
number of hours has elapsed.
4. With "ON" or "OFF" showing at 3: Press the appropriate Set Time button a
as necessary to set the hours to ON (if "ON" is displayed) or the hours to OFF
(if "OFF" is displayed) at 4.
• Available Range: 1 to 72 hours
5. To set both the ON and OFF times, repeat Steps 3 and 4.
* Note that ON and OFF times cannot be set to the same value.
6. To clear the current ON or OFF setting: Display the ON or OFF setting (see
Step 3) and then press the Check (Clear) button 0 so that the time setting
clears to "—" at 4. (If you want to use only an ON setting or only an OFF
setting, be sure that the setting you do not wish to use is shown as "—".)
7. After completing Steps 3 to 6 above, press the Filter
the value.
Note:
Your new settings will be cancelled if you press the Mode (Return) button 2
before pressing the Filter button 4.
8. Press the Mode (Return) button 2 to return to the standard control screen.
9. Press the Timer On/Off button 9 to start the timer countdown. When the
timer is running, the timer value is visible on the display. Be sure that the
timer value is visible and appropriate.
Hr ON
AFTER
SIMPLE
1
ON/OFF
b
FILTER
4
CHECK TEST
0
OPERATION
CLEAR
3
Action (On or Off)
* "— —" is displayed if there is no
setting.
1
SIMPLE
button 4 to lock in