Operation - EINHELL TC-SM 2131/1 Dual Mode D'emploi

•
Finally, check the position of the pointer (20)
on the scale (19).
•
If necessary, release the pointer (20) with a
crosstip screwdriver, move to the 0° position
of the scale (19) and retighten the holding
screw.
•
The angle stop (a) and crosstip screwdriver
are not included in the scope of this delivery.
5.6 Precision adjustment of the stop for miter
cut 45° (Fig. 7, 9)
•
Lower the machine head (4) and fasten in
place with the retaining pin (25).
•
Fasten the turntable (17) in 0° position.
•
Undo the locking lever (21) and move the ma-
chine head (4) all the way to the left using the
handle (1), until it coincides at 45°.
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (17).
•
Adjust the adjustment screw (29) so that the
angle between the blade (7) and the turntable
(17) equals exactly 45°.
•
To set the stop 45° on the right-hand side: Tilt
the machine head (4) to the right (see section
5.3) and set the adjustment screw (30) accor-
ding to the left-hand side.
•
No angle stop (b) included.

6. Operation

Warning! To make 90° crosscuts, the adjustable
stop rail (34) must be fi xed at the inner position:
•
Undo the locking screw (9) of the adjustable
stop rail and push the adjustable stop rail
inwards.
•
The adjustable stop rail (34) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (34) and
the saw blade (7) amounts to a maximum of
8 mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (9) again.
Warning! To make 0°-45° miter cuts to the left
(with the machine head (4) inclined or with the
turntable set at an angle), the adjustable stop rail
(34) must be fi xed at an outer position.
•
Undo the locking screw (9) of the adjustable
stop rail and push the adjustable stop rail
outwards.
•
The adjustable stop rail (34) must be fixed far
enough in front of the innermost position that
GB
the distance between the stop rail (34) and
the saw blade (7) amounts to a maximum of
8 mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (9) again.
Warning! This saw is equipped with a removable
stop rail (36) which is screwed to the right-hand
side of the fi xed stop rail (11).
To make 0°-45° miter cuts to the right (with the
machine head (4) inclined or with the turntable
set at an angle), the removable stop rail (36) must
be completely removed. Warning! In this case the
maximum permissible workpiece height is redu-
ced (see 4. Technical data).
•
Open the locking screw (9) of the removable
stop rail (36) far enough for you to be able to
remove the stop rail (36) in upwards direction.
•
Always fasten the removable stop rail (36) on
the equipment again after you have comple-
ted your work.
•
The stop rail must always be kept together
with the equipment. A removed stop rail will
impair the operational safety of the equip-
ment.
6.1 Cross cut 90° and turntable 0° (Fig. 1-3,
11)
For cutting widths up to approx. 100 mm it is
possible to fi x the saw's drag function with the
locking screw for drag guide (24) in rear position.
If the cutting width exceeds 100 mm you must
ensure that the locking screw for drag guide (24)
is slackened and that the machine head (4) can
be moved.
•
Move the machine head (4) to its upper po-
sition.
•
Use the handle (1) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
•
Place the piece of wood to be cut at the stop
rail (11) and on the turntable (17).
•
Lock the material with the clamping device
(8) on the fixed saw table (18) to prevent the
material from moving during the cutting ope-
ration.
•
Push down the release lever (3) to release the
machine head (4).
•
Press the On/Off switch (2) to start the motor.
•
With the drag guide fixed in place: Use the
handle (1) to move the machine head (4)
steadily and with light pressure downwards
until the saw blade (7) has completely cut
through the workpiece.
- 28 -