User Control Menu; System Setting Menu - Sony LMD-2110MD Instructions D'utilisation

Submenu
MANUAL
ADJUSTMENT

USER CONTROL menu

The USER CONTROL menu is used for adjusting the
picture.
Items that cannot be adjusted depending on the input
signal are displayed in black.
For details of input signal and adjustable / setting items,
see page 39.
USER CONTROL
C O N T R O L
C O N T R A S T :
B R I G H T N E S S :
C H R O M A :
P H A S E :
A P E R T U R E :
B A C K L I G H T :
Submenu
CONTROL
48
Adjustment Using the Menus
Setting
If you set the COLOR TEMP to
USER setting, the item displayed is
changed from black to white, which
means you can adjust the color
temperature.
• ADJUST GAIN: Adjusts the
color balance (GAIN).
• ADJUST BIAS: Adjusts the
color balance (BIAS).
• COPY FROM: If you select
HIGH, LOW or LOW2, the
white balance data for the
selected color temperature
will be copied in the USER
setting.
xx
xx
xx
xx
x
x
Setting
You can adjust the picture.
• CONTRAST: Adjusts the
picture contrast.
• BRIGHTNESS: Adjusts the
picture brightness.
• CHROMA: Adjusts color
intensity. The higher the
setting, the greater the
intensity. The lower the
setting, the lower the
intensity.
• PHASE: Adjusts color tones.
The higher the setting, the
more greenish the picture.
The lower the setting, the
more purplish the picture.
• APERTURE: Adjusts the picture
sharpness.
The higher the setting, the
sharper the picture. The
lower the setting, the softer
the picture.
• BACKLIGHT: Adjusts the
backlight. When the setting
is changed, the brightness of
the backlight is changed.

SYSTEM SETTING menu

The SYSTEM SETTING menu is used for setting the
system. You can set the display language and so on.
Items that cannot be adjusted depending on the input
signal are displayed in black.
SYSTEM SETTING 1/2
R G B / C O M P S E L :
C O M P O N E N T L E V E L :
N T S C S E T U P :
S C A N :
G A M M A :
F O R M AT D I S P L AY:
L A N G U A G E :
B A C K G R O U N D :
I / P M O D E :
SYSTEM SETTING 2/2
S D P I X E L M A P P I N G
C O M P O S I T E & Y / C :
R G B / C O M P O N E N T :
Submenu Setting
RGB/COMP SEL When a signal input via the RGB/
COMPONENT connector is being
monitored, based on the signal
being input, select RGB or COMP
(component).
COMPONENT LEVEL Selects the component level from
among three modes.
• SMPTE: for 100/0/100/0 signal
• BETA7.5: for 100/7.5/75/7.5
• BETA0: for 100/0/75/0 signal
NTSC SETUP Selects the NTSC setup level from
two modes.
The 7.5 setup level is used mainly
in North America. The 0 setup level
is used mainly in Japan.
SCAN Sets the scan size of the picture.
Select from OFF and FULL.
The display format changes
depending on the mode selected.
(See "Scan mode image" on page
50.)
• OFF: Changes between over scan
• FULL: Changes to over scan,
GAMMA Select the appropriate gamma
mode. You can select from among
five settings. When "3" is selected,
the setting is roughly same as the
gamma mode of the CRT (2.2).
xxx
xxxxx
x
xxxxxx
xx
xx
E N G L I S H
xx
x
xxxxxxx
xxxxxxx
signal
and normal scan.
normal scan or full screen.