Operation - EINHELL RT-CS 190/1 Mode D'emploi D'origine

Anleitung_RT_CS_190_L_SPK7:_
GB
45°. Keep an eye on the cutting angle scale (9) as
you do so.
Refasten the locking lever for miter setting (7).
Check the handle is securely fastened.
5.3 Precision adjustment of the miter stop to 0°
or 90° (Figure 6/7)
With a 90° angle stop you can adjust the angle setting
to 0° or 90°. To do so, undo the locking screw for the
miter stop (7) and the counternut (b) on the
adjustment screw (a). (See Figure 6) Turn the hand-
held circular saw upside down and place the angle
stop (c) between soleplate (6) and saw blade (12).
(See Figure 7) Now set the adjustment screw (a) until
the angle between the soleplate (6) and saw blade
(12) equals 90°.
Retighten the counternut (b) and the locking screw for
the miter stop (7).
5.4 Extraction of dust and chips (Figure 8)
Connect your circular saw to a suitable vacuum
cleaner with the dust extractor adaptor (15). Then
fit the dust extraction adaptor (15) into the
intended sawdust extraction outlet (14) on the
hand-held circular saw. You can then connect a
suitable vacuum cleaner to the dust extractor
adaptor (15) (vacuum cleaner not supplied). This
will provide excellent dust extraction on the
workpiece. The benefits are that you will protect
both the equipment and your own health. Your
work area will also be cleaner and safer.
Dust created when working may be dangerous.
Refer to the section entitled "Safety instructions".
Important! The vacuum cleaner you use for the
extraction work must be suitable for the
workpiece material.
Check that all the parts are properly connected.
5.5 Parallel stop (Figure 9/10)
The parallel stop (16) enables you to saw parallel
lines.
Loosen the locking screw for the parallel stop (8)
on the saw foot (6).
To assemble, slide the parallel stop (16) into the
guide (a) on the saw foot (6) (see Figure 9)
Set the required spacing and then tighten the
locking screw (8) again.
Using the parallel stop: Position the parallel stop
(16) flat on the edge of the workpiece and start
the cut.
Important! Carry out a trial cut in a piece of
waste wood
18
28.02.2011 13:51 Uhr Seite 18
5.6 Line Guide (Figure 11)
Using the line guide (25) you can carry out exact cuts
following cutting lines marked on the workpiece.
Push the line guide (25) forward to have a better view.
The marks (a) and (b) show the cutting width of the
installed saw blade.
Use the mark (a) for the 0° or 90°angle setting.
and the mark (b) for the 45° angle setting.
For information on the angle setting see 5.2
Important. Carry out a trial cuts in a piece of
waste wood.

6. Operation

6.1 Working with the hand-held circular saw
Always hold the circular saw firmly.
The swing guard hood (19) is pushed back
automatically by the workpiece.
Do not use force!
Push forwards gently and evenly with the circular
saw.
The waste piece should be on the right-hand side
of the circular saw so that the wide section of the
support bench supports its full area.
If you are sawing down a line that has been
drawn, guide the circular saw along the
corresponding notch.
Clamp small pieces of wood securely before
sawing them. Never hold them with your hand.
Always follow the safety instructions. Wear safety
goggles.
Do not use defective saw blades or blades that
are cracked or broken.
Do not use any flanges / flange nuts whose bore
hole is larger or smaller than those in the saw
blade.
The saw blade must not be decelerated by hand
or by applying lateral pressure to the blade.
The swing guard hood must not jam and must
return to its initial position after the operation has
been completed.
Before you use the circular saw, check the
function of the swing guard hood with the mains
plug disconnected.
Before you use the machine, ensure that the
safety equipment such as the swing guard hood,
splitter, flanges and adjustment devices are in
working order and are correctly adjusted and
secure.
You can connect a suitable dust extraction
system to the dust extraction adapter (15).
Ensure that the dust extraction system is safely
and correctly connected.