UFESA AS3016E Mode D'emploi page 10

OUTLET FILTER
1
In order to replace the outlet filter (12) pick up the
vacuum cleaner handle, then press the fastenings on
the cover of the outlet filter and slide out the cover out
of the vacuum cleaner.
2
Remove the outlet filter frame out of the vacuum
cleaner.
3
Remove the outlet filter out of the frame fastenings.
If the outlet filter (12) is dirty, it may be rinsed with
running water. Remember to dry the filter, before its
reinstallation.
Due to safety reasons, it is vital never to
install a damp outlet filter.
4
Carefully put the new/rinsed filter onto all frame
fastenings.
● Place the cover in such a way that the two protrusions
situated in the bottom part of the cover find their way into
the holes in the body of the vacuum cleaner, and then
press the filter cover to snap the fastenings on the body.
A characteristic click notifies about a proper installation.
Always replace a damaged inlet filter
only with a brand new one.
Disassembly/assembly of the
"CYKLON" dust container
The vacuum cleaner is equipped with a removable
"CYKLON" dust container (a removable segment of
the vacuum cleaner) gathering all pollutants. When the
"CYKLON" dust container is full, it needs to be emptied.
1
The vacuum cleaner is equipped with a "CYKLON"
dust container full indicator (6). When the "CYKLON"
dust container full indicator (6) lights during operation
(with the nozzle or the brush lifted above the cleaned
surface) it means that the container is full and needs
to be emptied. In addition the "CYKLON" dust container
full indicator (6) may activate if the suction hose or the
elements attached to the suction hose are clogged.
2
Switch off the vacuum cleaner by pressing the "on/
off" button (7).
3
Unplug the appliance.
4
Press the side button on the end of the hose, and
then remove the end of the hose from the inlet hole of
the vacuum cleaner.
E
5
Press the fastening of the "CYKLON" dust container
(8) and remove the "CYKLON" dust container (16) from
the vacuum cleaner.
6
Place the "CYKLON" dust container over a waste
bin. Press the button on the "CYKLON" dust container
and its contents will fall out into the bin.
7
After emptying the container, snap its bottom shut.
The container must be tightly closed.
Otherwise the dust might enter the
vacuum cleaner chamber and the suction
power will be reduced.
8
Place the emptied "CYKLON" dust container into
the vacuum cleaner. A characteristic click notifies about
a proper installation.
Emptying the "CYKLON" dust container is necessary,
when:
a) the "CYKLON" dust container full indicator light is on,
b) the vacuum cleaner operates poorly,
c) the "CYKLON" dust container is full.
End of operation cleaning
and maintenance
1
Switch off the vacuum cleaner by pressing the "on/
off" button (7).
2
Unplug the appliance.
F
3
Wind the cord by pressing the cord rewind button (4).
While doing this hold the cord to make sure it is not
tangled and the plug does not hit the vacuum cleaner
housing.
4
Disconnect the telescopic tube from the nozzle or
brush.
5
Disconnect the telescopic tube from the hose.
6
Press the side button on the end of the hose, then
remove the end of the hose from the inlet hole of the
vacuum cleaner.
7
The vacuum cleaner may be stored in a vertical
position – just place the fastening hook of the
combination brush into the fastening of the combination
brush. The hose may be connected to the vacuum
cleaner. Yet it is necessary to make sure it is not bent to
hard during storing time.
Horizontal storage:
– place the fastening hook of the combination brush
into its fastening placed at the back of the vacuum
cleaner, near the cord exit.
G