Programming Telephones - Fermax DUOX PLUS Manuel D'installation Et De Programmation

ENGLISH
CITYLINE Pushbutton panel AMPLIFIER
5 channel cable
The call extension
module can be
used
PUT
CN1
NTRITT
CN1
Detail
Connect the 5
channel cable to the
keyboard (CN1):
1
leave the pin on the
4
right free.
7
A
ref. 7439

Programming Telephones.

1. With the telephone connected, press the programming button (you will hear a beep).
Upon releasing it, you will hear the programmed entrance.
(upon picking up the phone, it automatically activates the panel´s audio and a
conversation may be held with the person on the outdoor panel to indicate the house to
be programmed).
2. Enter the house number via the keypad and press %. A programming confirmation is
produced.
* The telephone will not function if it has not been programmed.
For more details see the DUOX PLUScod.97695 telephone instructions and the chapters in this
Section II: "DUOX PLUS Amplifier Calling Codes" and "Calling homes from the Direct Panel".
NOTES:
- The DUOX PLUS system uses 6 digit house terminal addresses.
- Programming is always done from the panel activated as MASTER.
- Any installation can only have one MASTER panel at a time, whether a single or multiple block
installation, or if configured as a sub-block, block or general entrance.
- Upon programming each phone, it inherits the upper part of the address the outdoor panel has
assigned, if it isn´t a general entrance panel.
- A outdoor panel is configured as a MASTER via the SW1 amplifier button. If the SW1 button is pressed
3 times quickly, it is activated as a MASTER panel and a confirmation tone sounds (beep-beep). It
can also be configured with a keypad code, without having to open the panel, see»Configuring the
Direct Panel» for more details.
The sequence is: Activate the panel as MASTER: 10 (beep) 1 (beep-beep).
- When a panel is selected as MASTER, it notifies the others of the situation and if another was
previously configured, it would automatically stop being so.
Pag 46
CN1
DUOX AMPLIFICADOR
CN1 AMPLIFIER
CN1 PACK EXTENSION
A
TYPE Nº B
EG C
+
D
BK
E
-
BK
SW1 F
DL2 SB
+
DL2
LED
Nº PL
-
IDIOMA
LANGUAGE +
SW1 PROG
-
ONE
EXIT
TO JP1
BUS
ONE
CN2 CN3 P2 B B C - S P1
NO NC BS
+ 2 1
NC
C
NO
ENTRADA/INPUT
CN1
ARRIVÉE/EINTRITT
CN1
UP
2 3
5 6
8 9
CN2
0 B SALIDA/OUTPUT
SORTIE/AUSGANG
SKYLINE Pushbutton panel AMPLIFIER
SPK
ON OFF
JP1
C
No
VERSION
:
6 channel
cable
MÓDULO TECLADO
KEYPAD MODULE
MODULE CLAVIER
TASTATURMODUL
1
4
7
A
ref. 7439
DUOX
AMPLIFICADOR
CN1 AMPLIFIER
CN1 PACK EXTENSION
A
TYPE Nº
B
EG C
D
BK
E
SW1 BK
SB F
DL2
DL2
LED
Nº PL
IDIOMA
LANGUAGE
SW1 PROG
ONE
EXIT
TO JP1
ONE BUS
CN2 CN3 P2 B B C NO NC BS - S
+ 2 1
NC
C
NO
ENTRADA/INPUT
ARRIVÉE/EINTRITT
CN1
UP
2 3
5 6
8 9
CN2
SALIDA/OUTPUT
0
B
SORTIE/AUSGANG
SPK
+
-
+
-
+
-
ON OFF
P1 JP1
C
No
VERSION
:
MÓDULO TECLADO
KEYPAD MODULE
MODULE CLAVIER
TASTATURMODUL