Philips Saeco HD 8323 Mode D'emploi page 19

the machine is too high for brewing coff ee.
• Prime the circuit as described in section 4.5 to make the
machine ready for use.
Note: the machine is ready when the
chine ready" light is steady on.
Important note: if it is not possible to brew a
cappuccino as described, prime the circuit as
explained in section 4.5 and then repeat the steps.
The same procedure can be used to heat other
beverages.
• After this operation, clean the steam wand with a wet
cloth.
9 CLEANING
Maintenance and cleaning can only be carried out when the
machine is cold and disconnected from the electric network.
• Do not immerse the machine in water or place any of its
parts in a dishwasher.
• Do not use spirit, solvents and/or aggressive chemical
agents.
• We recommend cleaning the water tank and refi lling it
with fresh water every day.
• Clean the steam wand weekly. Wash the steam wand with
a wet cloth and remove any milk residue.
• (Fig.28) - Empty and clean the drip tray every day.
• Use a soft, dampened cloth to clean the appliance.
• (Fig.17) - Perform the following operations to clean the
pressurized fi lter holder:
- (Fig.9) - remove the fi lter and wash it thoroughly with hot
water.
- remove the adapter (if any) and wash it thoroughly with
hot water.
- wash the internal part of the pressurized fi lter holder.
• Do not dry the machine and/or its parts using a microwave
and/or standard oven.
• (Fig.29) - Clean the seat for accessories with a damp cloth
every week to remove any coff ee or dust residues.
Note: do not wash the pressurized fi lter holder
in the dishwasher.
10 DESCALING
Limescale builds up with the use of the appliance; the machine
needs descaling every 1-2 months and/or whenever a reduc-
tion in water fl ow is noticed. Use the Saeco descaling product
"ma-
only.
In case of confl ict, priority must be given to
what is indicated in the operation and mainte-
nance manual over the instructions provided on sepa-
rately sold accessories and materials.
Use the Saeco descaling product (Fig. B). Its
formula has been designed to ensure better
machine performance and operation for its whole op-
erating life. If correctly used, it also avoids alterations
in the brewed product. Before starting a descaling cy-
cle make sure that: THE WATER FILTER (if used) HAS BEEN
REMOVED.
Never drink the descaling solution or any prod-
ucts dispensed until the cycle has been carried
out to the end. Never use vinegar as a descaling solu-
tion.
1 (Fig.10-11) - Insert the fi lter holder into the brew unit (8)
from the bottom and turn it from left to right until it locks
into place.
2 (Fig.1B) - Remove and empty the water tank.
3 (Fig.2) - Pour HALF the content of the Saeco concentrated
descaling solution into the water tank, then fi ll the tank
with fresh drinking water up to the MAX level.
4 Turn on the machine by pressing the ON/OFF button (11).
The indicator light (16) turns on.
(Fig.18) - Fill up (as described in chapter 7 of the manual)
2 cups of water (about 150 ml each) from the steam / hot
water wand and turn off the machine by pressing the ON/
OFF button (11); the light (16) turns off
5 Let the descaling solution take eff ect for approx. 15-20
minutes with the machine turned off .
6 Turn on the machine by pressing the ON/OFF button (11).
(Fig.18) - Fill up (as described in chapter 7 of the manual)
2 cups of water (about 150 ml each) from the steam / hot
water wand. Then turn the machine off by pressing the
ON/OFF button (11) and leave it off for 3 minutes.
7 Repeat the operations described in step 6 until the water
tank is completely empty.
8 (Fig.2) - Rinse the water tank with fresh drinking water
and fi ll it completely.
9 Place a container under the fi lter holder.
10 Switch on the machine by pressing the ON/OFF button (11);
turn the selection knob (15) to the "
means of the fi lter holder, dispense the whole content of
" position and, by
• 19 •