Publicité
Les langues disponibles
Les langues disponibles
2.3.
Technical specifications.
Maximum admissible flow
Minimum recommended flow
Hydraulic connections
Electrical connections
Maximum current
3.
INSTALLATION. (Fig. 1)
According to swimming pool construction type.
3.1.
Panel-structure swimming pools.
a)
Cutting the panel.
Remove the canvas from the panel.
Place the template (15) on the interior part of
the swimming pool panel, such that the distance
between the plane XY and the maximum height
of the structure is 400 mm. The plane XY must
be parallel to the maximum‑height plane of the
swimming pool.
Mark the 14 assembly holes and cut along the
dotted‑line zone of the template so as to mark the
cut outline on the panel.
Cut the outline and drill the holes marked on the
panel.
Take care not to damage the canvas.
b)
Pre‑assembly, with the canvas removed from the
panel and according to the drawing:
Clean the contact surfaces between the
gaskets (2), rear body (3) and counterflange (1)
and the panel of the swimming pool.
Stick a gasket (2) onto the counterflange (1).
(Fig. A)
Stick the remaining two gaskets (2) onto the rear
body (3) (according to drawing). (Fig. B - C)
Secure the counterflange (1) through the rear part
of the swimming pool panel, fit the rear body (3)
from the other side of the panel and hold it firmly
in place while the two screws (13) are driven into
the holes A and B. (Fig. D)
Ensure that the rear body (3) is in correct position.
The word "HAUT" must be at the top part. (Fig. E)
80 m
40 m
interior Ø 63
NC_M 1 ~ 230 V
NC_T_ 3 ~ 400 V
NC_M 16A
NC_T1 6.3A
NC_T2 10A
(Fig. 2)
c)
Assembly.
After fitting the canvas, fill the swimming pool with
/h
3
approximately 15 cm of water so that it is well
/h
3
tensioned.
Place the flange (5) on the canvas, seeking out
the right position and making use of the lip of
the protective plate (4) to position it. Insert the
screws (11) so that they pierce the canvas and
then drive them fully home. Avoid excessive force
when driving home the screws. (Fig. F)
Once all the screws are secured, cut the interior
part of the canvas with a cutter. (Fig. G)
Remove the protective plate (4) and stow it safely.
(Fig. H)
3.2.
Polyester swimming pools.
a)
Cutting the panel.
Place the template (15) on the interior part of
the swimming pool panel, such that the distance
between the plane XY and the maximum height
of the structure is 400 mm. The plane XY must
be parallel to the maximum‑height plane of the
swimming pool.
Mark the 14 assembly holes and cut along the
dotted‑line zone of the template so as to mark the
cut outline on the panel.
Cut the outline and drill the holes marked in the
panel.
b)
Pre‑assembly, according to the drawing:
Clean the contact surfaces between the
gaskets (2), rear body (3) and counterflange (1)
and the panel of the swimming pool.
Stick a gasket (2) onto the counterflange (1).
(Fig. A)
Stick a gasket (2) onto the rear body (3). (Fig. C)
Secure the counterflange (1) through the rear part
of the swimming pool panel, fit the rear body (3)
from the other side of the panel and hold it firmly
in place while the two screws (13) are driven into
the holes A and B. (Fig. D)
Ensure that the rear body (3) is in correct position.
The word "HAUT" must be at the top part. (Fig. E)
c)
Assembly.
Stick the gasket (2) to the flange (5). (Fig. I)
Place the flange (5) on the rear body (3). Drive
the screws (11) fully home. Avoid excessive force
when driving home the screws. (Fig. F)
Withdraw the protective plate (4) and stow it
safely. (Fig. H)
8
Instruction manual
(Fig. 3)
Publicité
