Publicité
Les langues disponibles
Les langues disponibles
• Avoid awkward hand positions where a sudden slip
could cause your hand to touch the sanding belt or
disc.
• When sanding a large piece of material, provide an ad-
ditional support at table height.
• Never sand an unsupported workpiece. Secure the
workpiece with the table or the fence. Exceptions are
the sanding of curved workpieces on the outside of the
sanding disc.
• Always clear the table, fence or sanding belt of scraps
or other objects, before turning the machine on.
• Do not perform any layout assembly or set-up work on
the table while the sanding machine is in operation.
• Switch the machine off and pull the power plug from
the socket when fitting or removing accessories.
• Never leave the working area of the sanding machine
while the tool is running, or as long as it has not come
to an absolute standstill.
m Proper Use
The machine meets the currently valid EU machine direc-
tive.
• The safety, working, and maintenance instructions and
the dimensions set forth in the specifications must be
observed.
• The applicable regulations for the prevention of acci-
dents and other, generally recognized safety rules must
be observed.
• The machine may only be used, maintained or repaired
by trained persons who are familiar with the machine
and have been informed about the dangers. Unauthor-
ized modifications of the machine exclude a liability
of the manufacturer for damages resulting from the
modifications.
• The machine may only be used with original accessories
and original tools of the manufacturer.
• Any other use is considered to be not intended. The
manufacturer excludes any liability for resulting dam-
ages, the risk is exclusively borne by the user.
m Residual Risks
The machine has been constructed according to the state
of the art and the recognized safety rules. Nevertheless,
single residual risks may occur during the operation.
• Risk of injuries for fingers and hands caused by the ro-
tating grinding roller in the case of an improper guid-
ance or support of the work piece to be ground.
• Risk of injury caused by hurling work pieces in case of
an improper support or guidance.
• Danger caused by electric current if inappropriate elec-
trical connecting lines are used.
• Furthermore, non obvious residual risks may exist in
spite of all measures taken.
• Residual risks can be minimized by carefully observing
the Safety Notes and the Intended Use as well as the
entire operating instructions.
Equipment Fig. 1–2
1
Base (packed separately)
2
Sanding frame
3
Traverse table
4
Lateral table
5
Motor
6
On/Off switch
7
Extraction nozzle
8
Sanding belt
9
Sanding stop plate
10 Cross cutting gauge
11 Table clamping
12 Shifting knob
13 Belt clamping bracket
14 Adjustment handle
Assembly
For logistical reasons, your machine is not completely as-
sembled.
We recommend attaching the machine to the base frame
with which it that is delivered.
Four screws are included for this purpose.
Lengthwise table with adjustable clamp, fig. 3
1 Screw the lengthwise table with the 2 locking handles
loosely.
2 Place the adjustable clamp through the lengthwise ad-
justment plane in the housing and secure it with the
2 spring pins. Adjust the table and the scale index to
90°.
Assembling the lateral table, fig. 4
1 Mount the lateral table on the frame with 4 hex bolts, 4
washers, 4 hex nuts and tighten it slightly by hand. Align
the lengthwise table into the corner and tighten.
2 Set the scale index to 90°.
Assembling the sanding stop collar, fig. 5
Mount the sanding stop collar with 2 socket screws on
the frame.
Mounting the suction hood, fig. 6
Mount the suction hood on the sanding table with a
round-head screw, washer and wing nut (A).
Mounting the switch, fig. 6
Attach the switch with 2 screws to the switch plate (B).
Mounting the sanding belt, fig. 7
1 The clamping lever allows the sanding belt to be tight-
ened or loosened.
2 To put the sanding band in place, the clamping lever
must point in the direction of the arrow (1).
3 Loosen the handles, so that the pinch pin is loos-
ened.
4 Lift up the protective shield (4) and place the sanding
belt on the rollers. Pay attention to the arrows indicating
the direction on the inner side of the sanding belt.
5 To tighten the sanding belt, turn the clamping lever in
the direction of the arrow (2).
6 Put the protective shield back in place and tighten the
handles (3).
english 11
Publicité
