MCS Master TR 3C Manuel D'utilisation Et De Maintenance page 9

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
• PROGRAM 3: Advanced program, only for qualified personnel.
• PROGRAM 4: Advanced program, only for qualified personnel.
During use, the remote room thermostat automatically locks the
keyboard. To unlock the keyboard of the remote room thermostat,
press the arrow buttons simultaneously "↑↓".
CAUTION: A SERIES OF SENSORS CHECK THAT THE HEAT-
ER IS OPERATING CORRECTLY AND STOPS THE APPLIANCE
IN THE EVENT OF A SERIOUS FAULT. THE HEATER WILL
NOT RESUME OPERATION AUTOMATICALLY, THIS MUST
BE PERFORMED MANUALLY. WAIT FOR THE HEATER TO
COOL DOWN COMPLETELY AND REMOVE ANYTHING WHICH
MIGHT HAVE BLOCKED THE HEATER (E.G. OBSTRUCTED
AN AIR VENT, IMPAIRED THE AIR SUPPLY, ETC.) AND FULLY
PRESS THE "RESET" BUTTON LOCATED AT THE BACK OF
THE HEATER. IF, AFTER A FEW ATTEMPTS TO RESUME OP-
ERATION, THE HEATER DOES NOT WORK, CONTACT THE
TECHNICAL SUPPORT SERVICE.
►►5.2. SWITCH-OFF:
►5.2.1. Turn off the heater with the "ON / OFF " button of the re-
mote room thermostat and leave the fan running until the heater is
completely turned off (if the keyboard of the remote room thermo-
stat is locked, press the arrow buttons simultaneously "↑↓").
►5.2.2. Disconnect the heater from the mains.
CAUTION: AVOID DISCONNECTING THE HEATER FROM THE
MAINS BEFORE THE FAN HAS COMPLETELY STOPPED MOV-
ING TO AVOID SERIOUS DAMAGE.
►►8. TROUBLESHOOTING
PROBLEM
The heater
1. Main power supply switch in position
doesn't work
"0 / OFF"
2. Incorrect setting of the remote room
thermostat
3. No power supply
4. Blocked heater
The motor
1. Faulty motor
doesn't work
2. Fan blocked
The heater
1. Remove room thermostat set to
doesn't heat
"VENTILATION"
2. Faulty internal appliance
Reduced airflow
1. Obstructed air vent
2. Faulty motor
POSSIBLE CAUSE
►►6. STORAGE
Always unplug the heater from the mains during a long downtime.
Put it back in a dry place and protected from dust. When the heater
is used again, check the condition of the power supply cable. If in
doubt regarding its state, contact the technical support centre. In
any case, have the technical support centre check that the heater
is working properly at least once a year and/or as required.
►►7. REMOTE ROOM THERMOSTAT
For correct operation, the heater must be connected to the mains
and have the main power switch set to position "I / ON". When the
remote room thermostat is activated, the heater can turn on at any
time when the temperature drops below the set temperature.
POSSIBLE SOLUTION
1. Set the main power supply switch to "I / ON"
2a. Turn on the heater using the "ON / OFF" button of the remote room
thermostat and select the desired mode
2b. Make sure the temperature set on the remote room thermostat is
higher than the outdoor temperature
3a. Insert the power supply cable correctly
3b. Make sure your mains power supply is working correctly
3c. Contact a support centre
4a. Turn the heater back on
4b. Contact the support centre
1. Contact the support centre
2a. Remove any obstructions
2b. Contact the support centre
1. Modify the setting of the remote room thermostat
2. Contact the support centre
1a. Remove any obstructions
1b. Contact the support centre
2. Contact the support centre
en
it
de
es
fr
nl
pt
da
fi
no
sv
pl
ru
cs
hu
sl
tr
hr
lt
lv
et
ro
sk
bg
uk
bs
el
zh

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Tr 9c

Table des Matières