Footplates; Footrests - Quickie SOPUR Easy Max Mode D'emploi

Wheel Locks Übersicht Übersicht
Extension for the Brake Lever
(Fig.5.6).
The extension for the brake lever can be
removed or folded down. The longer
lever helps to minimize the effort needed
to set the wheel locks.
CAUTION!
Mounting the wheel lock too close toward
the wheel will result in a higher effort to
operate. This might cause the brake lever
extension to break!
Leaning onto the brake lever extension while transferring will
cause the lever to break! Splashing water from tires might
cause the wheel lock to malfunction.
Compact Wheel Lock
Compact wheel locks are
underneath the seat sling and
are operated by pulling the wheel
locks towards the rear, in the
direction of the tyre. For the
wheel locks to operate correctly,
they must be pulled fully against
the stops, (Fig. 5.6.1).
CAUTION!
Incorrect mounting of the wheel lock will result in a higher effort
to operate.

Footplates

Footplates
(Fig.5.7).
There are two types of footplates:
platform and divided. They can be
flipped up to facilitate getting in and
get ting out of your wheelchair.
Lower Leg Length
By removing the setscrews (1),
the footrest can be adjusted to fit
any lower leg length. Remove
setscrews, set tubing with footrest
in the desired position, and reinsert
and tighten the setscrews (see the
page on torque). Make sure that the compo site plastic pad is in
the proper position under the setscrew. A minimum interval of
2.5 centimeters from the ground should always be maintained.
Width Adjustment Of The Footrests
If the footrest width needs to be
adjusted, please undo the screw
(1), set the desired width, by
positioning 1, 2 or 3 spacers (2)
from outer to the inner side and
then refit the screws, (Fig. 5.7.1).
Rev.B
Fig.5.6
Fig. 5.6.1
Fig.5.7
1
Fig. 5.7.1
1
2
Divided and Platform Footplates
(Fig.5.8-5.10).
Footplates can be flipped up to
facilitate getting in and getting out
of your wheelchair.
They can also be tilted to six
different angles relative to a level
surface. Tighten screw (1) firmly on
the outer side. By removing the
clips (2), the footplate can be
adjusted to three different positions
toward both the front and rear.
Loosen the adjustment screw (3) to
change the horizontal position of
the footplate. For this purpose, the
footplate must be flipped up. When
finished, make sure that all screws
have been properly tightened (see
the page on torque).
A minimum interval of 2.5 centi-
meters from the ground should
always be maintained.

Footrests

Various footboards are available.
These can be flipped up to make
it easier to transfer to/from the
chair. They are described
individually.
Footrest And Swing Away
Latch
When fitting the footrests these
are fitted in the swung-away
position (Fig. 5.11). Then simply
turn them inwards until the
interlock engages (1). To remove
the footrests, use the lever (2)
and swing the footrest outwards
and lift off. Check that the
footrest is correctly engaged.
WARNING:
The footrests are not designed
to be used to lift or carry the
wheelchairs with an occupant.
Hanger Play Adjustment
In case of play the hanger (Fig. 5.11.1) can be adjusted in the
field. The hanger pin (1) is tapered and the play can be reduced
when the pin is unscrewed slightly.
Take the hanger off the chair in using the release mechanism.
Fig.5.8
Fig.5.9
Fig.5.10
Fig. 5.11
2
1
Fig. 5.11.1
1
EASY MAX 15