Specified Conditions Of Use; User Groups; Care And Maintenance - Weller WX 1 Traduction De La Notice Originale

WARNING Fire hazard
Covering the soldering iron or the safety holder poses
a fire hazard. Always keep objects well away from the
soldering iron and safety holder.
Always keep objects well away from the soldering iron
•
and safety holder.
Keep all combustible objects, liquids or gases well away
•
from the hot soldering tool.
The mains cable must only be plugged into the mains
socket or adapter approved for this purpose. Check to
see if the mains voltage matches the ratings on the
nameplate. Make sure the machine is switched off before
plugging in.
Do not use the cable for purposes other than those for
which it is intended.Never carry the unit by the cable. Do
not use the cable to pull the plug out of the socket. Protect
the cable against heat, oil and sharp edges..
Be alert. Pay attention to what you are doing. Be smart
when using the unit. Do not use the soldering tool if you are
having difficulty concentrating.
Avoid abnormal posture. Arrange your work station in an
ergonomically correct way. Avoid bad posture when using the
unit, as this can lead to postural problems.
The soldering tool must be operated only in perfect
technical working order. Safety devices must not be
deactivated.
Faults and defects must be repaired immediately.
Before using the unit / tool, safety devices must be carefully
checked to make sure that they are functioning properly and
in the manner intended. Check that moving parts are func-
tioning properly and are not sticking, and whether parts are
damaged. All parts must be correctly fitted and must satisfy
all the requirements necessary to guarantee troublefree
operation of the unit.
Use the correct tool. Use only accessories or auxiliary de-
vices which are included in the list of accessories or appro-
ved for use by the manufacturer. Use WELLER accessories
or auxiliary devices on original WELLER equipment only. The
use of other tools and other accessories can cause injury.
Secure the tool. Use clamping fixtures to hold the
workpiece.
Use a solder fume extraction unit. If appliances for
connecting solder fume extraction units are available, ensure
that they are connected and used properly.

Specified Conditions Of Use

Supply unit for WELLER WX soldering tools. Use the solde-
ring station / desoldering station / hot air station exclusively
for the purpose indicated in the operating instructions of sol-
dering and desoldering under the conditions specified herein.
WARNING
Flammable gases and liquids may not be extracted.
The device may only be used with correctly fitted and
suitable filter cartridges.
Replace filter cartridges when full.
This device may only be used at room temperature and
indoors. Protect against moisture and direct sunlight.
We hereby declare that the products described herein com-
ply with the following guidelines:
2014/30/EU, 2006/95/EG, 2011/65/EU (RoHS)

User groups

Due to differing degrees of risk and potential hazards, sever-
al work steps may only be performed by trained experts.
Work step
Default soldering para-
meters
Replacing electrical repla-
cement parts
Default maintenance
intervals
Operation
Filter change
Operation
Filter change
Replacing electrical repla-
cement parts

Care and maintenance

WARNING
Before doing any work on the machine, pull the plug out
of the socket. Leave the unit to cool down.
Clean the operator panel, if dirty, using a suitable cleaning
cloth.
Seal ports which are not in use with covering caps.
Check all connected cables and hoses on a regular basis. If
power tools are damaged, they must be immediately
removed from use.
WARNING Risk of burns
Only replace solder tips when cold
•
Replace and clean suction nozzles only when hot and
•
using the suitable tool
Only replace hot air nozzles using the suitable tool
•
Only clean or replace solder collection tubes when cold
•
Filter change
Regularly check the main filter for vacuum, and replace it if
necessary.
GB
ENGLISH
User groups
Specialist personnel with
technical training
Electricians
Safety expert
Non-specialists
Technical trainees under the
guidance and supervision of a
trained expert
17