Before Starting The Equipment; Adjusting The Handle; Cutting Grass; Cutting Hedges - EINHELL BG-CG 7,2 Li Mode D'emploi

Anleitung_BG_CG_7_2_Li_SPK7:_
Output
Rated voltage
Rated current
Sound and vibration were measured in accordance
with EN ISO 3744.

5. Before starting the equipment

5.1. Charging the battery pack (Figure 1/5)
Connect the equipment to the charger (Figure 5).
Check that your mains voltage is the same as that
marked on the rating plate of the battery charger.
Plug the battery charger in a socket-outlet. The
red LED (Figure 5/Item 1) comes on to indicate
that charging voltage is available.
The battery pack is being charged. An empty
battery pack requires a maximum charging period
of 3 to 5 hours. The temperature of the battery
pack may rise slightly during the charging
operation. This is normal.
As soon as battery pack is fully charged, the red
LED (Figure 5/Item 1) extinguishes.
If the battery pack fails to charge, please check
whether there is voltage at the socket-outlet
If you still fail to charge the battery pack, please return
the complete tool together with the battery charger to
our Customer Service Center.
Timely recharging of the battery will help it serve you
well for a long time. You must recharge the battery
pack when you notice that the power of the tool
drops.
Never allow the battery pack to become fully
discharged. This will cause it to develop a defect.
5.2. Fitting the long handle
Using the telescopic long handle (Fig. 1/Item 5) you
can push the cordless shears on wheels over the
lawn.
Now pass the wheels (Fig. 3/Item 2) through the axle
mount and plug together to fit the long handle. The
equipment comes with three axle mounts for various
work height.
Undo the clamp coupling (Fig. 1/Item 6), adjust the
telescopic handle to the required length and then re-
tighten the clamp coupling again. Now push the
equipment in the direction indicated by the arrow into
the mount as shown in Figure 4a. Ensure that the
13.02.2009 10:26 Uhr Seite 11
mount locks into the recesses correctly. Push the lock
(Fig. 4b/Item 2) in the direction indicated by the arrow
9 V DC
to fasten the equipment. Then connect the power
300 mA
plug (Fig. 4b/Item 1) to the equipment as shown in
Figure 4b.
To disassemble, proceed in reverse order.
Important.
The switching arrangements installed on the tool
by the manufacturer must not be removed or
bypassed, e.g. by fitting a switching button to
the handle, as this may result in risk of injury
and the tool will no longer switch off
automatically.

5.3 Adjusting the handle

The handle can be turned -90/-45/+45/+90 by pulling
the lock (Fig. 4c/Item 8) in the direction indicated by
the arrow. Take care to engage it correctly. The
appliance can now be used, for example, as an edge
trimmer.
6. Operation
The area to be cut must first be cleared of stones and
other solid objects. The safety lock-off (Fig. 1/Item 3)
prevents the tool being started unintentionally.
Activate the safety lock-off (Figure 1/Item 3) by
pressing and pressing the ON/OFF switch (Figure 1
Item 4) at the same time. To switch off the equipment,
let go of the ON/OFF switch (Figure 1 / Item 4).

6.1. Cutting grass

Allow the grass cutter to glide over the ground. The
best cutting performance is achieved on dry lawns.
When you notice a drop in cutting performance,
recharge at once so that the batteries do not become
fully discharged.
The blades must be kept in the black guard hood
when the grass cutter is not in use.

6.2. Cutting hedges

The equipment can be used to cut small hedges and
bushes.
Hold the shrub shears slightly tilted in the direction of
the hedge you wish to cut.
Start by cutting the sides of the hedge working from
the bottom up, and finally cut the top of the hedge.
Make sure that there are no foreign bodies in or
alongside the hedge, which could damage the
blades.
GB
11