Technical Data; Before Putting The Machine Into Operation - EINHELL 43.407.40 Mode D'emploi

Anleitung NTK 1200 SPK1
GB
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved."

5. Technical data

Voltage
Power rating
Idle speed n 0
Carbide saw blade Ø 210 x Ø 30 x 2.5 mm
Number of teeth
Table size
Table size with width extension
Max. table size with width extension 525 x 620 mm
Cutting height max.90°
Cutting height max.45°
Connector for dust extractor
Safety insulated
Weight
6. Before putting the machine into
operation
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong stand.
All the covers and safety devices have to be
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
16
25.07.2006 16:11 Uhr Seite 16
7. Assembly
Always pull out the power plug before carrying
out any maintenance or conversion work.
7.1 Fitting the saw blade (Fig. 2/3)
Important! Pull out the power plug.
Loosen the chip bin cover (19) by undoing the
fixing screws (20) and swing it up.
Undo the nut with a ring wrench (30) on the nut
itself and a second wrench (31) on the motor
shaft (32) to apply counter-pressure.
Important! Turn the nut in the direction of
rotation of the saw blade (4).
Take off the outer flange and pull the old saw
blade (4) off the inner flange by dropping the
blade at an angle.
230 V ~ 50 Hz
Clean the mounting flange.
1200 W
Fit the new saw blade in reverse order.
Important! Note the direction of rotation (see
4500 rpm
arrow on the saw blade).
20 7.2 Adjusting the splitter (Fig. 4/5/6)
Remove the saw blade guard (2) (see 7.3).
525 x 400 mm
Take out the table insert (6) (see 7.4).
525 x 470 mm
Slacken the two hexagon socket-head screws
(24).
Adjust the splitter (5) so that the gap between the
45 mm
saw blade (4) and the splitter (5) equals 3 - 5 mm
(see Fig. 6)
41 mm
The splitter (5) has to be in line with the saw
dia. 36 mm
blade (4) in longitudinal direction.
II / ® Retighten the two screws (24).
The setting of the splitter has to be checked each
15.7 kg
time after changing the saw blade.
7.3 Fitting the saw blade guard (Fig. 4)
Mount the saw blade guard (2) on the splitter (5)
and align.
Insert the screw through the hole in the saw
blade guard (2) and in the splitter (5) and secure
it with the wing nut.
To remove the saw blade guard, proceed in
reverse order.
7.4 Replacing the table insert (Fig. 4/5)
Important: Remove the power plug!
Remove the 6 screws (23).
Take off the saw blade guard (2) (see 7.3).
Lift the worn table insert (6) up and out.
Fit the replacement table insert by following the
above in reverse.