Bosch POF 1200 AE Notice Originale page 25

POF 1400 ACE: The lamp slowly goes out.
Note: For safety reasons, the On/Off switch 22
cannot be locked; it must remain pressed during
the entire operation.
Constant Electronic Control (POF 1400 ACE)
Constant electronic control holds the speed
constant at no-load and under load, and ensures
uniform working performance.
Adjusting the Depth-of-cut
(see figure D)
The adjustment of the depth-of-cut may on-
ly be carried out when the router is
switched off.
For coarse adjustment of the depth-of-cut, pro-
ceed as follows:
– Place the machine with the router bit mount-
ed on the workpiece to be machined.
– POF 1400 ACE:
– Set the fine-adjustment path to the centre
position with the adjustment knob 18. For
this, turn the adjustment knob 18 until the
marks 19 match as shown in the figure. After-
wards, set the scale 17 to "0".
19
– Set the step buffer 9 to the lowest position;
the step buffer engages noticeably.
– POF 1200 AE: Screw the adjusting screws
for the step buffer 24 halfway in or out.
– Loosen the wing bolt for the depth stop 11
so that the depth stop 13 can be moved free-
ly.
– Push the clamping lever for locking of routing
depth 16 in rotation direction
slowly lower the plunge router until the rout-
er bit 21 touches the surface of the work-
piece. Let go of the clamping lever 16 again
to lock this plunging depth.
Bosch Power Tools
If required, push the clamping lever 16 in ro-
tation direction
– Push the depth stop 13 downward until it
rests on the step buffer 9. Set the slide with
the index mark 12 to the "0" position on the
scale for the depth-of-cut adjustment 14.
– Set the depth stop 13 to the required depth-
of-cut and tighten the wing bolt for the depth
stop 11. Pay attention not to misadjust the
slide with the index mark 12 again.
– Push the clamping lever 16 in rotation direc-
tion
position.
For deep cuts, it is recommended to carry out
several cuts, each with little material removal.
By using the step buffer 9, the cutting process
can be divided into several steps. For this, ad-
just the desired depth-of-cut with the lowest
step of the step buffer and select the higher
steps first for the initial cuts.
POF 1200 AE: The clearance of the steps can be
changed by screwing the adjusting screws 24
further in or out.
Fine Adjustment of the Depth-of-cut
(POF 1400 ACE)
After a trial cut, the depth-of-cut can be set ex-
actly to the desired measure by turning the ad-
justment knob 18; turn in clockwise direction to
increase the cutting depth and in anticlockwise
direction to decrease the cutting depth. The
scale 17 can be used for guidance. One full turn
corresponds with a setting range of 2.0 mm; a
graduation mark on the top edge of the scale 17
corresponds with a 0.1 mm change of the set-
ting range. The maximum setting range is
± 8 mm.
Example: The desired depth-of-cut is to be
10.0 mm; the trial cut resulted in a cutting depth
of 9.6 mm.
– Lift up the router and place, e. g., a piece of
scrap wood under the guide plate 7 so that
the router bit 21 cannot touch the workpiece
and and
when lowering it. Push clamping lever 16 in
rotation direction
plunge router until the depth stop 13 faces
against the step buffer 9.
to lock it in place.
and guide the router to the uppermost
and slowly lower the
1 609 929 S76 | (21.7.09)
English | 25