Additional Safety Warnings; Residual Risk - Milwaukee M18 FCHS Notice Originale

Removing buttress roots
A buttress root is a large root extending from the trunk of the tree
above the ground. Remove large buttress roots prior to felling.
Make the horizontal cut into the buttress rst, followed by the
vertical cut. Remove the resulting loose section from the work area.
Follow the correct tree felling procedure after you have removed
the large buttress roots.
Limbing a tree
Limbing is removing the branches from a fallen tree. When limbing,
leave larger lower limbs to support the log o the ground. Remove
the small limbs in one cut. Branches under tension should be cut
from the bottom up to avoid bindingthe chain saw.
Bucking a log
Bucking is cutting a log into lengths. It is important to make sure
your footing is rm and your weight is evenly distributed on both
feet. When possible, the log should be raised and supported by the
use of limbs, logs or chocks.
Follow the simple directions for easy cutting. When the log is
supported along its entire length, it is cut from the top (overbuck).
GB
When the log is supported on one end, cut 1/3 the diameter from
the underside (underbuck). Then make the nished cut by overbu-
cking to meet the rst cut.
When the log is supported on both ends, cut 1/3 the diameter from
the top (overbuck). Then make the nished cut by underbucking the
lower 2/3 to meet the rst cut.
When bucking on a slope always stand on the uphill side of the log.
To maintain control when "cutting through", release the cutting
pressure near the end of the cut without relaxing your grip on the
chain saw handles. Don't let the chain contact the ground. After
completing the cut, wait for the saw chain to stop before you move
the chain saw. Always stop the motor before moving from tree to
tree.
Cutting springpoles
A springpole is any log, branch, rooted stump, or sapling which
is bent under tension by other wood so that it springs back if the
wood holding it is cut or removed.
On a fallen tree, a rooted stump has a high potential of springing
back to the upright position during the bucking cut to separate
the log from the stump. Watch out for springpoles—they are
dangerous.
WARNING! Springpoles are dangerous and could strike
the operator, causing the operator to lose control of the
chain saw. This could result in severe or fatal injury to the
operator. This should be done by trained users.

ADDITIONAL SAFETY WARNINGS

Some regions have regulations that restrict the use of the machine.
Check with your local authority for advice.
Never allow children or people unfamiliar with the instructions
to use the machine. Local regulations may restrict the age of the
operator.
Ensure before each use that all controls and safety devices function
correctly. Do not use the machine if the "o " switch does not stop
the motor.
Do not wear loose tting clothing, short trousers, or jewellery of
any kind.
English
22
Secure long hair so it is above shoulder level to prevent entangle-
ment in moving parts.
Beware of thrown, ying, or falling objects. Keep all bystanders,
children, and animals at least 15 m away from the work area.
Do not operate in poor lighting. The operator requires a clear view
of the work area to identify potential hazards.
Use of hearing protection reduces the ability to hear warnings
(shouts or alarms). The operator must pay extra attention to what is
going on in the work area.
Operating similar tools nearby increases both the risk of hearing
injury and the potential for other persons to enter your work area.
Keep rm footing and balance. Do not overreach.
Overreaching can result in loss of balance and can increase the risk
of kickback.
Keep all parts of your body away from any moving part.
Inspect the chain saw before each use. Check for correct operation
of all controls, including the chain brake. Check for loose fasteners,
make sure all guards and handles are properly and securely
attached. Replace any damaged parts before use.
Do not modify the machine in any way or use parts and accessories
which are not recommended by the manufacturer.
WARNING! If the machine is dropped, su ers heavy impact
or begins to vibrate abnormally, immediately stop the
machine and inspect for damage or identify the cause of
the vibration.Any damage should be properly repaired or
replaced by an MILWAUKEE service station.
Do not dispose of used battery packs in the household refuse or
by burning them. Milwaukee Distributors o er to retrieve old
batteries to protect our environment.Do not store the battery pack
together with metal objects (short circuit risk).
Use only System M18 chargers for charging System M18 battery
packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it o immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.

RESIDUAL RISK

Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise in use and the operator should pay special
attention to avoid the following:
• Injury caused by vibration
Always use the right tool for the job. Use designated handles.
Restrict working time and exposure.
• Damage to hearing due to exposure to noise
Wear hearing protection and limit exposure.
• Injury caused by contact with exposed saw teeth of the chain
• Injury caused by thrown-out pieces of the workpiece (wood
chips, splinters)
• Injury caused by dust and particles
• Injury to the skin caused by contact with lubricants
• Parts ejected from the saw chain (cutting/injection hazards)
• Unforeseen, abrupt movement, or kickback of the guide bar
(cutting hazards)"