Preparation - Gardena PowerJet 18V P4A Mode D'emploi

DANGER! Risk of explosion!
v Do not use the product in enclosed rooms or to blow flour,
sand, wood dust, etc.
1. SAFETY
IMPORTANT!
Read the operator's manual carefully before use and keep for future
reference.
Symbols on the product:
Read operator's manual.
Keep bystanders away.
Wear eye and ear protection.
Switch off:
Remove the Battery before cleaning or maintenance.
Do not expose to rain.
For the charger:
Remove plug from the mains immediately if the cable is
damaged or cut.
General safety warnings
Electrical safety for the charger
DANGER! Electric shock!
Risk of injury due to electric shock.
The product must be supplied through a residual current device (RCD)
v
having a rated residual operating current not exceeding 30 mA.
Safe operating practices
1 Training
a) Read the instructions carefully. Be familiar with the controls and the correct
use of the machine.
b) Never allow children or people unfamiliar with these instructions to use the
machine. Local regulations can restrict the age of the operator.
c) Keep in mind, that the operator or user is responsible for accidents or hazards
occurring to other people or their property.

2 Preparation

a) Obtain ear protection and safety glasses. Wear them at all times while
operating the machine.
b) While operating the machine always wear substantial footwear and long trou-
sers. Do not operate the machine when barefoot or wearing open sandals.
Avoid wearing clothing that is loose fitting or that has hanging cords or ties.
c) Do not wear loose clothing or jewellery that can be drawn into the air inlet.
Keep long hair away from the air inlets.
d) Operate the machine in a recommended position and only on a firm, level
surface.
e) Do not operate the machine on a paved or gravel surface where ejected
material could cause injury.
f) Before using, always visually inspect to see, that the shredding means, shred-
ding means bolts and other fasteners are secure, the housing is undamaged
and that guards and screens are in place. Replace worn or damaged compo-
nents in sets to preserve balance. Replace damaged or unreadable labels.
g) Before use, check the supply and extension cord for signs of damage or
aging. If the cord becomes damaged during use, disconnect the cord from
the supply immediately.
DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY.
Do not use the machine if the cord is damaged or worn.
h) Never operate the machine while people, especially children, or pets are nearby.
3 Operation
a) Before starting the machine, make certain that the feeding chamber is empty.
b) Keep your face and body away from the feed intake opening.
c) Do not allow hands or any other part of the body or clothing inside the feeding
chamber, discharge chute, or near any moving part.
d) Keep proper balance and footing at all times. Do not overreach. Never stand
at a higher level than the base of the machine when feeding material into it.
14890-20.960.01.indd 9
e) Always stand clear of the discharge zone when operating this machine.
f) When feeding material into the machine be extremely careful that pieces of
metal, rocks, bottles, cans or other foreign objects are not included.
g) If the cutting mechanism strikes any foreign objects or if the machine should
start making any unusual noise or vibration, immediately shut off the power
source and allow the machine to stop. Disconnect the machine from the sup-
ply and take the following steps before restarting and operating the machine:
– inspect for damage;
– replace or repair any damaged parts;
– check for and tighten any loose parts.
h) Do not allow processed material to build up in the discharge zone; this may
prevent proper discharge and can result in kickback of material through the
intake opening.
i) If the machine becomes clogged, shut-off the power source and disconnect
the machine from supply before cleaning debris.
j) Never operate the machine with defective guards or shields, or without safety
devices.
k) Keep the power source clean of debris and other accumulations to prevent
damage to the power source or possible fire.
l) Do not transport this machine while the power source is running.
m) Stop the machine and remove plug from the socket. Make sure that all
moving parts have come to a complete stop:
– whenever you leave the machine,
– before clearing blockages or unclogging chute,
– before checking, cleaning or working on the machine.
n) Do not tilt the machine while the power source is running.
4 Maintenance and storage
a) When the machine is stopped for servicing, inspection, storage, or to change
an accessory, shut off the power source, disconnect the machine from the
supply and make sure that all moving parts are come to a complete stop.
Allow the machine to cool before making any inspections, adjustments, etc.
Maintain the machine with care and keep it clean.
b) Store the machine in a dry place out of the reach of children.
c) Always allow the machine to cool before storing.
d) When servicing the shredding means be aware that, even though the power
source is switched off due to the interlock feature of the guard, the shredding
means can still be moved.
e) Replace worn or damaged parts for safety. Use only genuine replacement
parts and accessories.
f) Never attempt to override the interlocked feature of the guard.
5 Additional safety instructions for units with bagging attachments
Switch-off the machine before attaching or removing the bag.
Additional safety warnings
Battery safety
Read all the safety and general instructions.
Failure to observe the safety and general instructions may result in electric shock,
fire and / or serious injury.
Store these instructions in a safe place. Only use the charger if you can
fully evaluate all functions and carry them out without restrictions, or if you have
received corresponding instructions.
v Supervise children during use, cleaning and maintenance.
This will ensure that children do not play with the charger.
v Charge only lithium-ion batteries of the POWER FOR ALL system type
PBA 18V with a capacity of 1.5 Ah or more (5 battery cells or more).
The battery voltage must match the battery charging voltage of the
charger. Do not charge any nonrechargeable batteries.
Otherwise there is a risk of fire and explosion.
v
Do not expose the charger to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
v Keep the charger clean. Dirt poses a risk of electric shock.
v Always check the charger, cable and plug before use. Stop using the
charger if you discover any damage. Do not open the charger yourself,
and have it repaired only by a qualified specialist using only original
replacement parts.
Damaged chargers, cables and plugs increase the risk of electric shock.
v Do not operate the charger on an easily ignited surface (e. g. paper,
textiles, etc.) or in a flammable environment.
There is a risk of fire due to the charger heating up during operation.
v In order to avoid safety hazards, if the power supply cord needs to be
replaced, this must be done by GARDENA or by a customer service centre
that is authorised to repair GARDENA power tools.
v Do not operate the product while it is charging.
Products sold in GB only: Your product is fitted with an BS 1363/A approved
electric plug with internal fuse (ASTA approved to BS 1362). If the plug is not
suitable for your socket outlets, it should be cut off and an appropriate plug fitted
in its place by an authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug. The severed plug must be
disposed of to avoid a possible shock hazard and should never be inserted into
a mains socket elsewhere.
v These safety warnings apply only for lithium-ion batteries of the
POWER FOR ALL system PBA 18V.
9
23.09.20 12:51