Computer Instructions; Replacing The Batteries - Christopeit Sport AL 1 Notice De Montage Et D'utilisation

Computer instructions

The supplied computer allows the most convenient training. Every value
relevant to training is displayed in a corresponding window.
From the beginning of the training session, the required time, the current
speed, the approximate calorie consumption, the travelled distance ad the
current pulse rate are displayed. All values are counted from zero upwards.
If you wish to see one value displayed constantly during training, select this
with the „F" key. If you wish to see these values in constant alternation,
select the „SCAN" function. The display then changes from one function to
the next at intervals of approx. 6 seconds.
The computer is switched on by briefly pressing the F- key or simply by
beginning training. The computer begins to register and display all values.
To stop the computer, just stop training. The computer stops all
measurements and retains the last attained values. The last attained values in
the functions TIME, CALORIES and KM are stored and training can continue
with these values when training is resumed.
The computer switches of automatically approx. 4 minutes after training
is stopped. All values attained until that time are stored and are displayed
again when training is resumed. It is then possible to continue training from
these values or to reset all functions to zero using the L- key.
Displays:
1. „SPEED" (KM/H) display:
The current speed is displayed in kilometres per hour. It is not possible to
specify a particular value using the „E" key. The values last attained by this
function are not stored. (Limit of the display: 999.9 km/h.)
2. „TIME" (ZEIT) display:
The currently required time is displayed in minutes and seconds. It is possible
to specify a particular value using the „E" key. If a particular time
has been specified, the remaining time is displayed. When the specified value
is attained, this is indicated by an acoustic signal. The values last attained
by this function are stored. (Limit of the display: 99 minutes.)
3. „DIST (KM)" display:
The current status of the travelled distance is displayed. It is possible to
specify a particular value using the „E" key. If a particular distance has been
specified, the remaining distance is displayed. When the specified value is
attained, this is indicated by an acoustic signal. The values last attained by
this function are stored. (Limit of the display: 999,9 km.)
4. „CALORY" (CAL) display:
The current status of the consumed calories is displayed. It is possible to
specify a particular value using the „E" key. If a particular consumption
has been specified, the remaining number of calories to be consumed
is displayed. When the specified value is attained, this is indicated by an
acoustic signal. The values last attained by this function are stored. (Limit
of the display: 999,0 calories.)
5. „PULSE" display:
The current pulse rate is displayed in beats per minute. It is possible to
specify a particular value using the „E" key.
The values last attained by this function are not stored. (Limit of both displays:
40 – 240 pulse beats per minute.)
Note:
For pulse measurement, the two contact surfaces of the pulse measuring
handle unit must be gripped simultaneously. The contact surfaces should
be located centrally in the palms of the hands.
6. „SCAN" function:
If this function is selected, the current values of all functions are displayed
successively in a constant sequence approx. every 5 seconds.
7. „STOP" display:
Display of Stopmode. Presets can be set.
Keys:
1. „F" key (Fuction):
Pressing this key once briefly makes it possible to change from one function
to another, i.e. the respective functions can be selected for which entries
can be made using the „E" key. The currently selected function is indicated
in the window.
2. „E" key (Enter):
By pressing this key once, it is possible to specify values step by step in the
respective functions. For this, the desired function must firstly be selected
using the „F" key.
Holding the key pressed activates faster running. When training begins, the
specified values are then counted down to zero.
3. „L"-key = (Delete):
When this key is pressed briefly, the values chosen with the „F" key are
reset to zero. If the key is held longer (approx. 3 seconds), all last attained
values are deleted.
AAA batteries

Replacing the batteries:

1. Open the battery compartment cover and then remove the used Batteries.
(If the batteries should leak remove them under increased considering that
the battery acid is not into contact with skin come and clean the battery
compartment thoroughly.)
2. Insert the new batteries (type (AAA) 1.5 V in the correct order and taking
into account the polarity in the battery compartment and close the battery
cover so that it clicks into place.
3. If the computer does not pick up immediately, the function should Batteries
are removed for 10 seconds and re-inserted.
4. The empty batteries properly in accordance with the disposal regulations
disposed of and do not give residual waste.
21
Battery compartment