Items Included - Bosch GCM 18V-216 Professional Notice Originale

moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.

Items included

See the list of items included at the start of
the operating manual.
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Sliding mitre saw with mounted saw blade
– Dust bag (2)
– Transport handle (4), two screws for assembly
– SDS bolt (48)
– Screw clamp (26)
– Hex key (41)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Charging the Battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Removing the battery (see figure A)
The battery (34) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release button
(35) is pressed unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
Bosch Power Tools
To remove the battery (34), press the release button (35)
and pull the battery forwards and out of the power tool. Do
not use force to do this.
Battery charge indicator (see figure B)
For safety reasons, it is only possible to check the state of
charge when the power tool is not in operation.
Battery model GBA 18V...
The three green LEDs of the battery charge indicator (42) in-
dicate the state of charge of the battery (34). Press the but-
ton (43) to show the state of charge. This is also possible
when the battery is removed.
LED
Continuous light 3 x green
Continuous light 2 x green
Continuous light 1 x green
Flashing light 3 x green
If no LED lights up after pressing the button (43), then the
battery is defective and must be replaced.
Battery model ProCORE 18V...
The five green LEDs of the battery charge indicator (42) in-
dicate the state of charge of the battery (34). Press the but-
ton (43) to show the state of charge. This is also possible
when the battery is removed.
LED
Continuous light 5 x green
Continuous light 4 x green
Continuous light 3 x green
Continuous light 2 x green
Continuous light 1 x green
Flashing light 1 x green
If no LED lights up after pressing the button (43), then the
battery is defective and must be replaced.
Fitting the transport handle (see figure C)
– Screw the transport handle (4) into the corresponding
threads with the screws supplied.
Stationary or flexible mounting
To ensure safe handling, the power tool must be
u
mounted on a flat, stable work surface (e.g. work
bench) before use.
English | 31
Capacity
60−100%
30−60%
5−30%
0−5%
Capacity
80−100%
60−80%
40−60%
20−40%
5−20%
0−5%
1 609 92A 4UN | (05.06.2019)