Cardin Elettronica GL Série Manuel D'instructions page 21

REMOTE CONTROL (fig. 1 page 3)
The system can be remotely activated using radio control devices.
Each channel can be set to a maximum of 2 functions:
- function 1: sequential command "TD"
- function 2: blocking button "TB"
To set one of the functions to the channels A-B-C-D use the selec-
tion jumpers "J2"
- in position "A" you can select function 1, TD;
- in position "B" you can select function 2, TB .
The sequential command can be set (dip "1") to work as "open-block-
close-block" or "open-close".
Memory module (M1)
This is extractable, furnished with a non volatile EEPROM type
memory and contains the transmitter codes and allows you to memo-
rise up to 300 codes.
The programmed codes are maintained in this module even during
blackouts.
Note: Before memorising the transmitters for the first time remember
to cancel the entire memory content.
If the electronic card has to be replaced due to failure, the module can
be extracted from it and inserted into the new card. Make sure that
the module is correctly inserted as shown in fig. 1.
Signal LEDs "L4" (fig. 1):
Flashing quickly: cancels a single code
Flashing slowly: memorises a single code
Permanently lit: memory full.
TRANSMITTER CODE MANAGEMENT
Memorising a channel (fig. 1)
1. Press and hold down button "P2" MEMO: The LED "L4" will flash
slowly.
2. At the same time activate the transmitter which is to be memorised.
3. Hold down button "P2" MEMO until LED "L4" starts to flash again.
4. Release the button "P2" MEMO: The LED will continue to flash.
5. Activate the transmitter again (same transmitter, same channel; if the
channel is different or it is a different transmitter the memorization
attempt will abort without success).
6. End of memorization: the LED "L4" will remain lit for 2 seconds,
indicating that the transmitter has been correctly memorised.
Note: It is not possible to memorise a code which is already in memory:
if you attempt this, the LED will switch off when you activate the
transmitter (point 2).
Only after releasing the button "P2" MEMO will you be able to continue
the memorising procedure.
If after activating the transmitter for the first time you wait for more
than fifteen seconds without activating the transmitter a second time
the memorization attempt will abort without success.
Cancelling a channel (fig. 1)
1. Press and hold down the button "P3" DEL: the LED "L4" will flash
quickly.
2. Activate the transmitter channel which is to be cancelled.
3. The LED will remain lit for 2 seconds indicating that the transmitter
has been cancelled.
Note: If the user that you wish to cancel is not in memory, the LED
will stop flashing; only after releasing the button "P3" will you be able
to continue the cancellation procedure.
For both the memorization and cancellation procedures, if the button
is released before activating the transmitter the procedure will abort.
Cancelling all user codes from memory (fig. 1)
1. Keep both buttons pressed down ("P2+P3") for more than four
seconds.
2. LED "L4" will remain lit during the entire cancellation time (about 8
seconds).
3. LED "L4" switches off when the cancellation procedure has termi-
nated.
Note: When the memory is almost full the time required to search for
a user code could take up to 1 second from when the command was
received. If led "L4" remains lit memory is completely full. To memorise
a new transmitter you will first have to cancel a code from memory.
Memorising ulterior channels via radio
• Memorization can be activated by radio (without opening the receiver
container) only if DIP 9 is in position ON.
1. Make sure that DIP 9 is in position ON.
2. Using a transmitter, in which at least one
channel button "A, B, C or D" has already
been memorised in the receiver, press the
button in the transmitter as shown in figure.
Note: all the receivers within range when the channel button is pressed
(and which have at least one of the transmitter channel buttons memo-
rised) will activate their signal buzzer "B1" (fig. 1).
3. Press one of the channel buttons on the same transmitter. The
receivers which do not contain that channel code will sound a five-
second long "beep" and will then deactivate. The receivers which
contain the channel code will sound a one-second long "beep" and
will enter the "programming via radio" mode.
4. Press the previously chosen channel buttons on the transmitter
which you wish to memorise; the receiver will sound 2 "beeps" of
half a second each after which the receiver will be ready to receive
another code.
5. To leave the programming mode wait for 3 seconds without press-
ing any buttons. The receiver will sound a five-second long "beep"
and will then exit the programming mode.
Note: When the memory is entirely occupied the buzzer will sound
10 rapid "beeps" and will automatically leave the "programming via
radio" mode.
Led "L4" will remain lit on the receiver.
The same signal is given each time you try to enter "programming
via radio" when the memory is full.
CONNECTING THE ANTENNA
Connect an ANS400 tuned antenna using a coaxial cable RG58
(impedance 50Ω) with a maximum length of 15 m.
FUNCTION MODES
1) Automatic
This is selected by enabling automatic reclosing (dip "2" in position
"ON"). Starting from the completely closed position the sequential
command starts a complete function cycle that terminates with
automatic reclosing.
Automatic reclosing starts after the programmed pause period has
elapsed when the opening cycle has been completed or straight
away after the intervention of a photoelectric cell (the intervention of
a photoelectric cell causes the pause time to be reset).
During the pause time the symbol
pressing the blocking button during this period will stop automatic
reclosing and consequently stop the display from flashing.
2) Semiautomatic
Selected by deactivating automatic reclosing (dip "2" in position
"OFF"). Work cycle control using separate opening and closing com-
mands.
When the door has reached the completely open position the system
will wait until it receives a closing command either via an external
control button or via radio control, before completing the cycle.
Note: the integrated courtesy light switches on each time a move-
ment command is given; switching off occurs when the motor stops:
- after 60 seconds (with mains power supply);
- after 15 seconds (with battery powered operation).
The indicator lamp flashes slowly during opening and quickly during
closing; it remains lit when the door is not completely closed.
21
Description : MEMORIZZAZIONE CODICE TX-RX
Drawing number : DM0531
Product Code : RCQ449100
P.J.Heath Date : 13-04-2001
Draft :
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401
will flash on the display and