Options And Accessories - Hatco HCWBI Serie Manuel D'installation Et D'utilisation

OPTIONS AND ACCESSORIES

Pan Support Bars
The following pan support bars are available to divide the
heated wells into sections for different size pans.
HWBGM12BAR .... 12" (305 mm) Pan Support Bar
HWBGM20BAR .... 20" (508 mm) Pan Support Bar
Pan Platform (2-Pan)
12" Pan Support Bars
Pan Support Bars
Food Pans
Stainless steel food pans are available in various sizes.
ST PAN 1/3 ............ Third-size stainless steel pan — 12-3/4"W
x 6-7/8"D x 2-1/2"H (324 x 175 x 64 mm)
ST PAN 1/2 ............ Half-size stainless steel pan — 12-3/4"W x
10-3/8"D x 2-1/2"H (324 x 264 x 64 mm)
ST PAN 2 ............... Full size stainless steel pan at 2-1/2"
(64 mm) deep — 12-3/4"W x 20-3/4"D x
2-1/2"H (324 x 527 x 64 mm)
ST PAN 4 ............... Full size stainless steel pan at 4"
(102 mm) deep — 12-3/4"W x 20-3/4"D x 4"H
(324 x 527 x 102 mm)
ST PAN 6 ............... Full size stainless steel pan at 6"
(152 mm) deep — 12-3/4"W x 20-3/4"D x 4"H
(324 x 527 x 102 mm)
1/3 Pan
Full Pan,
2-1/2" (64 mm) Deep
Stainless Steel Food Pans
20" Pan Support Bar
1/2 Pan
Full Pan,
4" (102 mm) Deep
Flush Hose Kit
A Flush Hose Kit is available and is used to power flush the
Hydro-Heater to keep it working at peak efficiency. The kit
consists of a flush hose, drain stopper, cleaning brush, and
adapter. Use the following procedure to power flush the Hydro-
Heater.
1. Move the Power I/O/I (on/off/on) Switch to the center "O"
(off) position and allow the unit and water to cool.
2. Move the drain lever down to the
open position and allow the unit to
drain.
3. Place the rubber stopper into the
inlet strainer.
NOTE: The inlet strainer is the strainer
closest to the front of the well.
4. Attach the flush hose with adapter to a fresh water supply,
and place hose into outlet strainer. Flush fresh water
through the unit until the discharge from the drain is clear.
5. Turn off the fresh water supply, and reverse the positions
of the rubber stopper and the power flush hose. Flush
fresh water through the unit again until discharge from the
drain is clear.
6. Turn off the water supply, remove the rubber stopper and
power flush hose, and allow the unit to finish draining.
7. Place a catch pan below the
cleanout drain(s), remove the
pipe cap(s) from the drain(s) and
allow remaining water to empty
from the unit.
8. Insert cleaning brush into clean-
out drain(s) and use a scrubbing
motion to clean the tanks.
9. Rinse fresh water through the
unit until discharge is clear.
10. Reinstall the pipe cap(s) onto the cleanout drain(s).
11. Close drain by moving the drain handle all of the way
forward until it is completely vertical.
NOTE: Perform the entire "Daily Cleaning" procedure in the
MAINTENANCE section of this manual if buildup is
significant.
Four Year Extended Parts Warranty
A four year extended parts warranty on the compressor is
available at time of purchase. This warranty begins after the
standard one year warranty expires.
18
English
Drain Lever
in open
position.
Cleanout
Drain
Pipe Cap
Form No. HCWBIM-1017