Machine Configuration Menu; User Level; User Management - LORCH Basic Manuel D'utilisation

7

Machine configuration menu

‰ In this menu, it is possible to recall software versions (revi-
sion) and make settings to the machine configuration.
 Press the Menu button A2 for at least 5 sec. (the Second-
ary parameters menu opens after 2 sec. and the Machine
configuration menu opens 3 seconds after that)
9 You are now in the Machine configuration menu.
 Use the rotary knob A41 to select the desired parameter.
Code Parameter
red Display version number
reL Master version number
reP Process version number
reS Welding programs version
number
reF Feed version number
rEC WUK version number
rEE Remote version number
rE1 Primary version number
CoL Cooling system
Aut = Automatic, on = On, oFF = Off, 30 = 30 min. on;
The cooling device is available for the three welding processes
MIG/MAG, electrode and TIG and can be separately configured in
each case. To do this, first select the desired welding process and
then open the machine configuration menu.
When using a gas-cooled torch, on a water-
cooled power source, the cooler in the weld-
ing process MIG/MAG must be switched off!
Co2 CO2 optimisation for welding
processes, MIG/MAG Manual
A30
Con User level on switch-on (only
visible from user level 10)
CUL

User level

CCn Customer number
Sbt Standby
Tab. 3: Machine configuration parameters
- 18 -
Range
Aut Aut, on, oFF, 30
oFF on...oFF
8 0...8
8 0...15
OFF OFF, 5, 10, 15,
30, 45, 60, 90,
120 min
909.3039.9-02
Machine configuration menu
User level
This function allows user rights to be enabled on various lev-
els.
The switch-on user level Con 8 is set by default. This means
that all the welding functions are available when the device
is switched on.
This switch-on user level can be changed, e.g. to Con 0 (theft
protection). This means that the device is blocked after switch-
on. The user must then log in with their personal user card.
 Hold the user card on the NFC read surface A43 until the
code nFc appears in the left-hand 7-segment display A4
and the code oK appears in the right-hand 7-segment dis-
play.
CUL Name/function
0 Locked (Theft protection)
1 Robot control / Read only
(Robot control parameter
setting/for info only on user
interface.)
2 WPS Welder Basic
3 WPS Welder Advanced
(WPS Welder Advanced)
4 Welder Basic
(Welder Basic)
8 Welder Advanced
(Welder Supervision)
10 Administrator
Tab. 4: User level

User management

The function is shown using the example of Welding Supervi-
sor and WPS Basic users.
Welding Supervisor log-in:
 Hold the Welding Supervisor NFC card (user level 8) on the
NFC read surface A43 for at least 3 sec.
9 The code nFc appears in the left-hand 7-segment display
A4. After approx. 3 sec., the code oK appears in the right-
hand 7-segment display as log-in confirmation.
 Set the desired welding process, main and secondary pa-
rameters. (The setting values are applied for the WPS Basic
user)
WPS Basic user log-in:
 Hold the WPS Basic NFC card (user level 2) on the NFC read
surface A43 for at least 3 sec.
9 The code nFc appears in the left-hand 7-segment display
A4. After approx. 3 sec., the code oK appears in the right-
hand 7-segment display as log-in confirmation.
- - - -
X - - -
X - 10% -
X - 10% X
X X X -
X X X X
X X X X
01.20