Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
NOTE: The internal battery's percent
of charge is most accurate when the jump
starter has been disconnected from all
devices and charging sources
for a few hours.
4.2 CHARGING THE INTERNAL BATTERY
Charge the internal battery of the jump
starter using an extension cord (not
included).
NOTE: Use of an improper extension
cord could result in a risk of fire and
electric shock.
1. Plug an extension cord into the charger
port on the back of the jump starter.
2. Plug the extension cord into a 120VAC
electrical wall outlet. While the jump
starter is connected to an AC outlet, the
green LED on the back of the unit will
be on.
3. Monitor the progress of the charge by
pressing the display button on the front
of the unit. When the internal battery is
fully charged, the display will show 100.
Complete charging may take up to 72
hours. The jump starter is then ready
to use.
4. When fully charged, the charger will
automatically go into maintain mode
and maintain the battery at full charge
without damaging it.
5. Charge the jump starter as soon as
possible after use.
5. OPERATING INSTRUCTIONS
5.1 JUMP STARTING A VEHICLE
IMPORTANT: Using the Jump Start feature
without a battery installed in the vehicle will
damage the vehicle's electrical system.
1. Turn the ignition OFF.
2. Lay the DC cables away from any
fan blades, belts, pulleys and other
moving parts.
3. For a negative-ground vehicle (as
in most vehicles), connect the unit's
POSITIVE (RED) clamp to the
POSITIVE (POS, P, +) battery post.
Next, connect the NEGATIVE (BLACK)
clamp to the vehicle chassis or engine
block, away from the battery.
4. For a positive-ground vehicle, connect
the unit's NEGATIVE (BLACK) clamp
to the NEGATIVE (NEG, N, -) battery
post. Next, connect the POSITIVE (RED)
clamp to the vehicle chassis or engine
block away from the battery.
5. Turn the switch to the ON position.
4.3 CHARGING THE INTERNAL BATTERY
WHILE DRIVING
You may also charge the internal battery
while driving, using a male-to-male
charger cable (part number 94500109 –
not included).
IMPORTANT: DO NOT CHARGE
INTERNAL BATTERY FOR MORE THAN
30 MINUTES OR LEAVE THE BATTERY
UNATTENDED. IT COULD EXPLODE,
CAUSING PROPERTY DAMAGE OR
PERSONAL INJURY.
1. Make sure the car is running.
2. Insert one end of the accessory cable
into the 12V DC power outlet.
3. Insert the other end of the accessory
cable into the vehicle's accessory outlet
(lighter socket).
NOTE: The GREEN LED does not
operate during this method of charging.
Using this method to charge the battery
overrides the maintain mode and the
battery can be overcharged.
4. Monitor the progress of the charge by
pressing the display button on the front
of the unit. When the battery is fully
charged, disconnect the accessory
cable from the jump starter, then from
the lighter socket of the vehicle.
NOTE: Completely disconnect the charger
cable when the engine is not running.
NOTE: When connected to the vehicle,
the display shows the vehicle's battery
voltage. When connected and in the ON
position, the display shows the equalized
voltage between the vehicle's battery and
internal battery.
6. Crank the engine for no more than 8
seconds. If the engine does not start,
wait 2 minutes before cranking again.
7. After the engine starts, turn the switch to
the OFF position and remove the jump
starter from the battery.
8. Charge the unit.
5.2 USING THE USB PORT
The USB port provides up to 2A at 5V DC.
1. Ensure the battery clamps are securely
clipped on the storage holders.
2. Turn the unit ON.
3. Plug your device into the USB port.
4. When finished using the USB port, turn
the switch to the OFF position.
5. Charge the unit.
• 4 •
Publicité
Table des Matières
